Bedienungsanleitung Operating Manual Mode d'emploi Kabelmodem Cable modem Modem câble DCM 32 DCM 42 / 42 I Bestell-Nr./ Order No.
Inhalt / Contents / Sommaire Inhalt / Contents / Sommaire Inhalt / Contents / SommaireVorwort ............................................................. 3 Vorwort.............................................................................................................. 6 Anschlüsse und Anzeigen............................................................................... 7 Sicherheitshinweise.........................................................................................
Inhalt / Contents / Sommaire Anschlussschema.......................................................................................... 17 Preface ............................................................................................................ 18 Connections and displays............................................................................. 19 Safety instructions .........................................................................................
Inhalt / Contents / Sommaire Branchements et affichages ......................................................................... 31 Consignes de sécurité ................................................................................... 32 Remarques importantes concernant l'utilisation ..................................... 32 Absence prolongée / orage ................................................................. 32 Tension d'alimentation................................................................
Vorwort Vorwort Sehr geehrter Kunde, die neuen Kabelmodems DCM 32 (DOCSIS), DCM 42 und DCM 42 I (EURODOCSIS)*) von KATHREIN bieten ihnen über den Breitbandkabel-Anschluss einen Hochgeschwindigkeitszugang ins Internet. Sie verfügen damit über eine äußerst schnelle Verbindung ins Internet und ihr Telefonanschluss bleibt weiterhin erreichbar. Erschließen Sie sich das weite Tor zum Internet und genießen Sie mit nur einem Klick Videos und Musik oder holen Sie sich interessante Informationen.
Anschlüsse und Anzeigen Anschlüsse und Anzeigen LEDs (Erklärung auf Seite 14 ff) 1 2 3 1 Stromversorgung 12 V 2 HF-Buchse (F-Buchse) 3 Ethernet-Buchse 4 USB-Buchse 4 7
Sicherheitshinweise Sicherheitshinweise Wichtige Hinweise zum Betrieb Im folgenden Abschnitt finden sie wichtige Hinweise zum Betrieb, Aufstellungsort und Anschluss des Modems. Lesen sie diese Hinweise sorgfältig, bevor sie das Gerät in Betrieb nehmen. Längere Abwesenheit/Gewitter Trennen sie das Gerät bei längerer Abwesenheit und bei Gewitter grundsätzlich vom Strom- und Kabelnetz. Dies gilt auch für diejenigen Geräte, die mit dem Modem verbunden sind.
Sicherheitshinweise Reparatur Lassen sie Reparaturen nur von qualifiziertem Fachpersonal ausführen. Eigenmächtiges Öffnen und Reparaturversuche führen zu Garantieverlust. Durch unsachgemäße Eingriffe am Gerät kann die elektrische Sicherheit gefährdet werden. Der Hersteller haftet nicht für Unfälle des Anwenders am geöffneten Gerät. Anschlüsse Eine Fehlbeschaltung der Anschlüsse kann zu Betriebsstörungen oder zu Defekten am Gerät führen.
Aufstellungsort und Montage Aufstellungsort und Montage Aufstellungsort Jedes elektronische Gerät entwickelt Wärme. Die Erwärmung liegt jedoch in einem ungefährlichen Bereich. Empfindliche Möbeloberflächen und Furniere können sich durch die ständige Wärmeeinwirkung im Laufe der Zeit leicht verfärben. Ebenso können die Gerätefüße in Verbindung mit behandelten Möbeloberflächen Farbveränderungen hervorrufen. Stellen sie das Modem gegebenenfalls auf eine geeignete ebene Unterlage.
Aufstellungsort und Montage Netzspannung Betreiben sie das Modem über das mitgelieferte Steckernetzteil nur an einer Netzspannung von 230 V/50 Hz. Das Gerät darf erst an das Netz angeschlossen werden, nachdem die Verbindungen mit der Antennensteckdose und dem PC hergestellt wurden. Erdung Die Hausverteilanlage muss entsprechend den einschlägigen örtlichen und/oder VDEVorschriften geerdet sein.
Installation Installation Voraussetzungen Für den Betrieb des Kabelmodems müssen folgende Bedingungen erfüllt sein: Breitbandkabelanschluss mit Rückkanal, netzwerkfähiger PC (Ethernet 10/100Base-T oder USB 1.1). Anschlüsse Beim Anschluss des Kabelmodems gehen sie in folgender Reihenfolge vor, siehe Anschlussschema Seite 25: • Verbinden sie den HF-Eingang (2) des Modems mit der Antennensteckdose. Vergewissern sie sich vorher, dass die Steckdose rückkanalfähig ist, z.B. Kathrein ESM 30.
Installation sprechend den Anweisungen in der ReadmeDatei auf der Installations-CD vor. Bei Problemen mit dem Anschluss setzen sie sich bitte mit dem zuständigen Kabelnetzbetreiber in Verbindung. Verwenden sie zum Festdrehen der F-Stecker auf den F-Buchsen keine Werkzeuge. Ziehen sie die Stecker nur handfest an! Sobald das Modem ordnungsgemäß angeschlossen ist, nimmt es den Betrieb auf. Weitere Maßnahmen sind nicht erforderlich.
Betriebsanzeigen und Fehlerdiagnose Betriebsanzeigen und Fehlerdiagnose Zur Statusüberwachung und Fehlererkennung sind an der Frontseite des Kabelmodems fünf LEDs vorhanden: POWER leuchtet grün CABLE leuchtet grün PC blinkt oder leuchtet grün DATA blinkt oder leuchtet grün TEST dunkel (bei Test orange) Die Bedeutung der LEDs für die jeweiligen Betriebszustände: Funktion Status Power dunkel leuchtet grün Cable dunkel blinkt alle 5 s blinkt langsam PC Data Test Bedeutung keine Netzspannung Netzspannung vor
Technische Daten Technische Daten Das DCM 32 ist nach MCNS DOCSIS 1.0, 1.1, 2.0 und das DCM 42/42 I nach EURODOCSIS 1.0, 1.1, 2.0 spezifiziert.
Technische Daten DCM 32 Frequenzbereich DCM 42 / 42 I Frequenzbereich 5 bis 42 MHz (Eckfrequenzen) 5 bis 65 MHz (Eckfrequenzen) SNMP Management MIB Group MIB II, MCNS MIB Ethernet USB RF Betriebsspannung Leistungsaufnahme IEEE802.3/10/100Base-T USB 1.1 F-Buchse 75 Ω 12 V= 9 W (max.
Anschlussschema Anschlussschema Kabelanschluss Netz EthernetKabel USB 10BASE-T RF DC IN Koaxkabel USB-Kabel Sehr geehrter Kunde, sollten sie mit ihrem Modem wider Erwarten Probleme haben, setzen Sie sich bitte mit ihrem zuständigen Kabelnetzbetreiber in Verbindung.
Preface Preface Dear Customer, the new cable modems DCM 32 (DOCSIS), DCM 42, and DCM 42 I (EURODOCSIS)*) from KATHREIN provide you with high-speed access to the Internet via the broadband cable connection. While you now have an extremely fast connection to the Internet at your disposal, your telephone connection still remains accessible. Open up the wide portal to the Internet and with just one click enjoy videos and music or simply fetch interesting information.
Connections and displays Connections and displays LEDs (Explanation on page 26) 2 3 1 Power supply 12 V 2 RF input (F socket) 3 Ethernet socket (Western) 4 USB Series B socket USB 10BASE-T RF DC IN 1 4 19
Safety instructions Safety instructions Important notes regarding operation The following section contains important information as to the operation, place of installation and connection of the receiver. Read these notes carefully before putting the unit into operation. Extended absence/thunderstorms Always disconnect the unit from the power and cable networks during periods of extended absence or at the onset of thunderstorms. This also applies to any other equipment connected to the modem.
Safety instructions Repairs If repairs are needed, get a qualified specialist to carry them out and nobody else. Unauthorised opening and attempts at repairs entail loss of guarantee. Electrical safety can be put at risk by tampering with the unit. The manufacturer’s liability excludes accidents occurring to the user when the unit is opened. Connections Incorrect wiring up of the connections can result in operational failure or to defects on the unit.
Putting into operation Putting into operation Every electronic device generates heat. The rise in temperature, however, lies within a safe range. Slight colour changes may occur to sensitive furniture surfaces and veneers over the course of time due to the constant effect of heat. Colour changes may also be brought about if the unit‘s feet are in contact with treated furniture surfaces. Place the modem on a suitable smooth pad where necessary.
Putting into operation Mains voltage Run the modem via the accompanying plug-in power adapter off a mains voltage of 230 V/50 Hz only. The unit must not be connected to the supply until after the connections to the antenna socket and the PC have been set up. Grounding The house distribution system must be grounded in accordance with the relevant local and/or German VDE regulations. RF-connection Do not remove the cable connection (F-plug) from the modem while it is still connected to the mains supply.
Installation Installation Preconditions For operation of the cable modem the following conditions need to be satisfied: Broadband cable connection with backward channel, Network-compatible PC (Ethernet 10/100Base-T or USB 1.1). Connections When connecting the cable modem, follow the steps below in order, see wiring diagram on page 29. • Connect the RF input (2) of the modem to the antenna socket. Make certain beforehand that the socket has backward channel capability, e.g. Kathrein ESM 30.
Installation provider if problems occur with the line. Do not use any tools to tighten the F-plugs on the F-sockets. Tighten the plug connectors hand-tight only! As soon as the modem is connected properly, it commences operation. No further measures are required. It now automatically finds the data channel, logs on to the computer and commences communication with the computer.
Status indicators and error diagnosis Status indicators and error diagnosis There are five LEDs on the front panel of the cable modem to monitor status and show errors: POWER lights up green CABLE lights up green PC flashes or lights up green DATA flashes or lights up green TEST not lit (orange on test) The meaning of the LEDs for the respective operational states is shown below.
Specifications Specifications The DCM 32 corresponds to the specification MCNS DOCSIS 1.0,1.1, 2.0. The DCM 42 corresponds to the specification EURODOCSIS 1.0,1.1, 2.0.
Specifications DCM 32 Frequency range DCM 42 / 42 I Frequency range 5 MHz to 42 MHz (edge frequencies) 5 MHz to 65 MHz (edge frequencies) SNMP management MIB Group MIB II, MCNS MIB Ethernet USB RF IEEE802.3/10Base-T USB 1.1 F socket, 75 Ω Voltage supply Power consumption 12 VDC 9 W (max.
Connection scheme Connection scheme Cable connection Mains Ethernet cable USB 10BASE-T RF DC IN Coaxcable USB cable Dear Customer, In the unlikely event that you should experience problems with your modem, please contact your relevant cable network provider.
Avant propos Avant propos Cher Client, Les nouveaux modems DCM 32 (DOCSIS), DCM 42 et DCM 42 I (EURODOCSIS)*) de Kathrein vous offrent un accès à vitesse élevée à l'internet via une connexion par câble large bande. Vous disposez ainsi d'une liaison extrêmement rapide à l'internet et votre ligne téléphonique reste libre. Ouvrez en grand la porte de l'internet pour profiter de clips vidéos et musicaux à portée d'un clic de souris ou pour aller chercher des informations intéressantes.
Branchements et affichages Branchements et affichages Voyants (explication à partir de la page 35) 2 3 USB 10BASE-T RF DC IN 1 4 1 Alimentation 12 V 2 Prise HF (embase type F) 3 Prise Ethernet (Western) 4 Prise USB 31
Consignes de sécurité Consignes de sécurité Remarques importantes concernant l'utilisation Vous trouverez dans le paragraphe suivant des remarques importantes sur l'utilisation, le lieu d'installation et le raccordement du modem. Lisez attentivement ces remarques avant de mettre en service l'appareil. Absence prolongée / orage En cas d'absence prolongée ou d'orage, débranchez toujours l'appareil du secteur et du réseau câblé. Ceci s'applique également à tous les appareils raccordés au modem.
Consignes de sécurité Réparation Faites réparer votre modem uniquement par des techniciens qualifiés. Toute ouverture de l'appareil et toute tentative de le réparer de votre propre initiative entraînent la perte de la garantie. Des interventions non qualifiées sur l'appareil peuvent en compromettre la sécurité électrique. Le fabricant décline toute responsabilité en cas d'accidents survenus à l'utilisateur si l'appareil était ouvert.
Lieu d'installation et montage Lieu d'installation et montage Lieu d'installation Tout appareil électronique produit de la chaleur. L'élévation de température reste cependant dans des limites non dangereuses. La surface de certains meubles ou des placages sensibles peuvent changer légèrement de teinte au cours du temps suite à une action permanente de ce dégagement de chaleur. De même, les pieds de l'appareil en contact avec certaines surfaces de meuble fragiles peuvent provoquer des variations de teinte.
Lieu d'installation et montage Tension d'alimentation N'utilisez le modem qu'avec l'adaptateur secteur livré avec le modem et branché seulement à une tension secteur de 230 V / 50 Hz. L'appareil doit être branché sur le secteur seulement après que les liaisons à la prise d'antenne et au PC ont été effectuées. Mise à la terre L'installation de distribution individuelle doit correspondre aux prescriptions locales en vigueur et/ou à celles de l'UTE.
Installation Installation Conditions préalables Pour le fonctionnement du modem, les conditions suivantes doivent être satisfaites : Raccordement pour câble large bande avec canal de retour, PC avec adaptation pour réseau (Ethernet 10/100Base-T ou USB 1.1). Raccordements Pour brancher le modem câble, procédez dans l'ordre précisé ci-dessous, cf. schéma des connexions en page 25. • Reliez l'entrée HF (2) du modem à la prise d'antenne.
Installation En cas de problèmes de raccordement, veuillez contacter l'exploitant responsable du réseau câblé. N'employez pas d'outils pour serrer les fiches F sur les prises ou embases F. Un serrage à la main de ces fiches est suffisant ! Dès que le modem est correctement branché, il se met en service, d'autres mesures ne sont pas nécessaires. Il trouve automatiquement le canal de données, contacte l'ordinateur et établit une communication avec l'ordinateur.
Affichages de service Diagnostique d'erreur Affichages de service Diagnostique d'erreur Pour surveillance du statut et reconnaissance d’erreurs il y a cinq LEDS sur la surface frontale du modem câble: POWER resplendit en vert CABLE resplendit en vert PC clignote ou resplendit en vert DATA clignote ou resplendit en vert TEST foncé (pendant Test orange) La signification der LEDs pour chaque état d’ exécution Fonction Statut Power foncé resplendit en vert Cable foncé clignote chaque 5 s clignote lentement PC
Affichages de service Diagnostique d'erreur 39
Caractéristiques techniques Caractéristiques techniques Le DCM 32 est spécifié selon MCNS DOCSIS 1.0, 1.1, 2.0 et le DCM 42 / 42 I selon EURODOCSIS 1.0, 1.1, 2.0.
Caractéristiques techniques DCM 32 Plage de fréquence DCM 42 / 42 I Plage de fréquence 5 MHz à 42 MHz (fréquences limites) 5 MHz à 65 MHz (fréquences limites) Gestion SNMP Groupe MIB MIB II, MCNS MIB Ethernet USB HF IEEE802.3/10/100Base-T USB 1.1 Embase type F 75 Ω Tension de service 12 V= Consommation 9 W (max.
Schéma des connexions Schéma des connexions Adaptateur secteur Branchement au réseau câblé Câble Ethernet USB 10BASE-T RF DC IN Câble coaxial Câble USB Cher Client, Si, contre toute attente, votre modem devait vous poser quelques problèmes, veuillez contacter l'exploitant du réseau câblé.
Notizen Notizen 43
Notizen 44
936.2456/C/0605/ZWT Technische Änderungen vorbehalten. Subject to alterations. Sous réserve de modifications techniques. Internet: http://www.kathrein.de KATHREIN-Werke KG • Phone ++49 80 31 184-0 • Fax ++49 8031 184-306 Anton-Kathrein-Straße 1 – 3 • P.O.