User's Manual
Table Of Contents
- 1 About this Document
- 2 General Information
- 3 Preconditions and Requirements
- 4 Installing the C-Hub
- 5 Installing the E-Hub
- 6 Installing the HPRU
- 7 Cabling
- 8 System Documentation
- 9 Glossary
- 10 List of Diagrams
- 11 List of Tables
- Fig. 1: Scope of delivery
- Fig. 2: Example of a handover point for the BTS signals at a c-rail
- Fig. 3: Example of a handover point for the BTS signals with individual loads with short patch cables at a c-rail
- Fig. 4: Clearance Ⓐ above radiation fins of the installed devices
- Fig. 5: Sliding rails Ⓑ
- Fig. 6: Power distribution bar ① mounted on the left-hand traverse
- Fig. 7: Plugs for power connection: ① is for red circuit, ② for black circuit
- Fig. 8: Attaching a 19" mounting bracket
- Fig. 9: Attached sliding rails Ⓑ
- Fig. 10: Place C-hub in rack
- Fig. 11: Fix C-hub with screws
- Fig. 12: Connect power cable at rear side
- Fig. 13: Connect ground cable at rear side
- Fig. 14: Attaching a 19" mounting bracket
- Fig. 15: Marking position of mounting holes
- Fig. 16: Mounting completed
- Fig. 17: Connect power cable at rear side
- Fig. 18: Connect ground cable at rear side
- Fig. 19: Attaching handle
- Fig. 20: Attaching bracket Ⓐ
- Fig. 21: Marking mounting holes for bracket Ⓑ
- Fig. 22: Prepare expansion bolts for bracket Ⓑ
- Fig. 23: Mounting accessories for bracket Ⓑ
- Fig. 24: Bracket Ⓑ mounted
- Fig. 25: Hook HPRU into bracket Ⓑ (①) and fix from top (②).
- Fig. 26: HPRU fixed from top
- Fig. 27: Fix HPRU from side
- Fig. 28: Connect power cable at bottom side
- Fig. 29: Connect ground cable at bottom side
- Fig. 30: Interfaces at the C-hub front side
- Fig. 31: Interfaces at the C-hub rear side
- Fig. 32: Interfaces at the E-hub front side
- Fig. 33: Interfaces at the E-hub rear side
- Fig. 34: Interfaces at the HPRU connector side
- Fig. 35: Fibre optical cable layout
- Fig. 36: Coaxial cable layout
- Fig. 37: Power supply cable layout
- Tab. 1: Symbols and signal words
- Tab. 2: Storage of the system documentation
63 of 64936.5468 0.92
11 List of Tables
Tab. 1: Symbols and signal words 5
Tab. 2: Band configuration parameters C-hub 36
Tab. 3: System configuration parameters C-hub 37
Tab. 4: System status parameters C-hub 38
Tab. 5: Combiner parameters C-hub 39
Tab. 6: LAN connectivity parameters C-hub 40
Tab. 7: Device alarm parameters C-hub 41
Tab. 8: Downlink input power alarm parameters C-hub 42
Tab. 9: Alarm threshold parameters C-hub 42
Tab. 10: Optical module information parameters C-hub 42
Tab. 11: Engineering parameters C-hub 43
Tab. 12: Factory command parameters C-hub 44
Tab. 13: LAN connectivity parameters E-hub 46
Tab. 14: Alarm parameters E-hub 46
Tab. 15: Alarm threshold parameters E-hub 47
Tab. 16: Optical module information parameters E-hub 47
Tab. 17: Engineering parameters E-hub 48
Tab. 18: Factory command parameters E-hub 48
Tab. 19: System configuration parameters HPRU 50
Tab. 20: System status parameters HPRU 51
Tab. 21: Channel actual gain parameters HPRU 51
Tab. 22: LAN connectivity parameters HPRU 52
Tab. 23: Alarm parameters HPRU 53
Tab. 24: Alarm threshold parameters HPRU 53
Tab. 25: Optical module information parameters HPRU 54
Tab. 26: Engineering parameters HPRU 55
Tab. 27: Factory command parameters HPRU 55
Tab. 28: Service configuration parameters HPRU 56
Tab. 29: Service switch parameters HPRU 56