MODEL GT-77 PARTS LIST 8/7/07 10:28 AM Page 1 SURE-FEED BROADCASTER Instructions for ASSEMBLY, MOUNTING, BROADCASTING, OPERATING and MAINTENANCE MODEL GT-77 FOR ATV’S REPAIR PARTS LIST HERD SEEDER COMPANY, INC. P.O. Box 448 • 2383 South U.S. 35 Logansport, IN 46947 Phone: 574-753-6311 • Fax: 574-722-4106 Email: info@herdseeder.com www.herdseeder.
MODEL GT-77 PARTS LIST 8/7/07 10:29 AM Page 2 MODEL GT-77 For ATV’s 69 WARNING SPINNING BLADES HAZARD To Prevent Serious Personal Injury or Death: KEEP HANDS, FEET AND CLOTHING AWAY FROM SPINNING BLADES. STAY CLEAR OF ALL MOVING PARTS WHEN IN OPERATION. KEEP OTHERS AWAY. KEEP ALL GUARDS IN PLACE. STOP MACHINE AND DISCONNECT POWER BEFORE ADJUSTING, LUBE OR SERVICE. Warning Decal - If missing Call 574/753-6311 for free replacement.
MODEL GT-77 PARTS LIST 8/7/07 10:29 AM Page 3 PARTS and ACCESSORIES FOR MODEL GT-77 BROADCASTER for A.T.V.’s Shown in Drawing When ordering parts, order by both part name and number ... not drawing number. Drawing Part Number Number 1. 500 3. & 4. 410A 8. 911 9. & 11. 912 10.,12.,13. 913 14. 778 15. 501 16. 502 17. 779 19. 812 23. 794 26. 541 30. 107 31. 512 32.,33.,34. 407 35.,36.,37. 924 42. 781 43. 44. & 45. 46. 47. 48. 49. 50. 51. 507 503 209 508L *517 802S 510 509 52. 53. 504 803S 54. 56. & 57.
MODEL GT-77 PARTS LIST 8/7/07 10:29 AM Page 4 ASSEMBLY INSTRUCTIONS FOR ALL A.T.V.’S.: 1. Take broadcast seeder GT-77 from carton and place it upside down on the hopper. 2. Rotate handle around and remove bolt and self-locking nut. Run bolt through seed-gate linkage, then through the handle, making sure that the thread end is pointing up, toward you. Replace self-locking nut. Do not over-tighten, as it must pivot at this point. 3.
MODEL GT-77 PARTS LIST 8/7/07 10:29 AM Page 5 TIPS FOR USING BROADCASTERS 1. WATCH YOUR SPEED! Do Not Go Too Fast For Conditions. If Ground Is Rough, Cut Your Speed. Remember when seeder is loaded it causes much strain on A.T.V.s and hitch brackets when you start bouncing through holes and rough ground. The hitches were designed for normal usage, so do not get carried away and go too fast. 2.
MODEL GT-77 PARTS LIST 8/7/07 10:29 AM Page 6 TO REPLACE VIBRATOR BUSHING ON FAN 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Remove nipple from pivot plate hole. Remove round head machine screw and bushing holding agitator to pivot plate. Move agitator forward and at the same time, turn fan so that agitator can be removed from bushing on top of fan. Remove agitator from opening.
MODEL GT-77 PARTS LIST 8/7/07 10:29 AM Page 7 CHART FOR HERD BROADCASTER GT-77 (Electric Motor Powered-Full Speed on 12 Volts) Spread Width Amount Per Acre Opening Width Speed MPH Clover, Alfalfa, and Sweet Clover 28’ 28’ 28’ 10# 6.6# 5# 1/8” 1/8” 1/8” 4 6 8 4 Min. 25 Sec. 2 Min. 57 Sec. 2 Min. 13 Sec. Bermuda Grass (Hulled) Set Base on H 22’ 22’ 22’ 9# 6-3/4# 5.4# 1/8” 1/8” 1/8” 6 8 10 3 Min. 45 Sec. 2 Min. 49 Sec. 2 Min. 15 Sec.
MODEL GT-77 PARTS LIST 8/7/07 10:29 AM Page 8 LIMITED WARRANTY This Herd Broadcaster was thoroughly tested before it left the factory. We warrant each Broadcaster sold by us to be free from defects in material and workmanship when used according to our directions. Our obligation under this warranty is limited to making good at the factory any defective part or parts thereof which shall, within three months after delivery of such Herd Broadcaster to the original purchaser, to be returned to us.
