Manual

ManualsBrandsKargo Master ManualsCar40963/40943) Drop Down Mechanism Only (40953

1



40963/40943PartsList



FrontTorqueTubePivotAssy.RearTorqueTubePivotAssy.



FrontLadderPanAssy.(1)RearLadderPanAssy.(1)



Latch(1)LadderHook(2)LadderStop(2)DampenerMntBrkt(2)Roller(2)Axle(2)Dampener(1)



NoDampenerMntBrktsin40943



TorqueTube(1)



LadderPanStiffener(1)



HandleAssy.(1)



Summary of content (8 pages)

PAGE 1
40963/40943 Parts List Front Torque Tube Pivot Assy. Rear Torque Tube Pivot Assy. Front Ladder Pan Assy. (1) Rear Ladder Pan Assy. (1) Latch(1) Ladder Hook(2) Ladder Stop(2) Dampener Mnt Brkt(2) Roller(2) No Dampener Mnt Brkts in 40943 Torque Tube (1) Ladder Pan Stiffener (1) Handle Assy.
PAGE 2
40963/40943 Installation Instructions Step 1 Bolt “Dampener mounting bracket” underneath the crossbow (both front and rear) as shown below using 3/8”x3/4 Bolts with flat and lock washers. Step 2 Bolt “Torque tube pivot Assy.” underneath the crossbow (both front and rear) as shown below using 3/8”x3/4 Bolts with flat and lock washers. Be sure to have the 3 hole flanges facing each other (rear bow shown). You may need to detach the feet and lift the crossbow slightly to get into place.
PAGE 3
Step 4 Next attach the “Dampener” to the rear bow assembly. Make sure the “Torque Tube Pivot Assy.” is rotated so the cam is pointed towards the center of the van. Attach the shaft end of the “Dampener” to the cam using the 5/16” pin, make sure the cotter pin is secure. Now attach the body end to the “Dampener mounting Bracket” using the 5/16”x2 1/4” pin. Step 5 Attach the “Latch” To the rear bow assy. as shown below using 5/16”x3/4” carriage bolts with flat washers and nylock nuts.
PAGE 4
Step 6 Next install the “Axles” and “Rollers” at the end of both front and rear crossbow. The “Axle” just slides in and the “Rollers” slide over the ends of the “Axle” as shown below. Step 7 Next install the “Ladder Pan Assy.” Align cutouts in “Ladder Pan Assy.” with the “Rollers” and guide the arms onto the “Torque Tube Pivot Assy.” As you lower the assembly onto the rollers. Insert 5/16”x 2” bolts with flat washer and nylock nuts through arms and “Torque Tube Assy.” Make sure the “Rear Ladder Pan Assy.
PAGE 5
Step 8 Install handle assembly, use E6000 on 5/16”x 2” bolts to keep water out of the tube. Be sure handle will clear the back of the van.
PAGE 6
Step 9 Attach ladder pan stiffener, in the closed position, using 5/16”x5/8” bolts with lock and flat washers.
PAGE 7
Step 10 Attach ladder hooks to ladder pans on 5/16” studs in desired location(Diagram A). Attach ladder stops to coincide with ladder hooks by removing 3/8”x3/4” bolt and placing stop so the tab on the stop goes into the corresponding slot. The diagram below shows in the lower position commonly used for extension ladders. You can install in the upper position in the rear for step ladders (as shown in last view).
PAGE 8
Installation Complete for Extension Ladder Installation Complete For Step Ladder 8