Owner manual

ManualsBrandsKarcher ManualsSpecial machineryB 40 W DOSE disc

QUICKSTART

5.964-243.0 04/12

Warning

These are only brief instructions! Please read and comply with these instructions prior to using or servicing your

appliance.

The non-compliance of the operating and safety instructions may lead to damages of the appliance and to dangers

for the operator and other persons.

Start up

A B A Unplug the charger from the mains.

B Wind the mains cable around the cable

holders.

A B A Open the lock of the fresh water reservoir.

Fill fresh water (maximum 60 °C) until the

lower edge of the filling nozzle.

Close the lock of the fresh water reservoir.

B Connect the hose to the automatic filling

system and open the water supply

(max. 60 °C, max. 5 bars).

Monitor the appliance - the automatic filling

system will interrupt the water supply when

the tank is full.

Shut off the water supply and disconnect the

hose from the appliance.

A Model with dosing equipment "Dose"

A Place the detergent bottle into the holder.

Close the bottle lid.

Insert the suction hose of the dosaging

equipment into the bottle.

Model without dosing equipment

"Dose"

A Add the detergent to the fresh water

reservoir.

Operation

A B Starting the machine

A Turn the program selection switch to "OFF".

B Plug in the Intelligent Key.

A B Driving

Turn the programme selector switch to position 1

"Transport mode".

Drive forward

A Press the driving lever to the front.

Stop the machine: Release driving lever.

Reverse drive

B Press the driving lever to the rear.

Stop the machine: Release driving lever.

B 40 W

Summary of content (7 pages)

PAGE 1
QUICKSTART B 40 W Warning These are only brief instructions! Please read and comply with these instructions prior to using or servicing your appliance. The non-compliance of the operating and safety instructions may lead to damages of the appliance and to dangers for the operator and other persons. Start up 1 A B A Unplug the charger from the mains. B Wind the mains cable around the cable holders. 2 A B A Open the lock of the fresh water reservoir.
PAGE 2
QUICKSTART Operation 3 Cleaning Programs A Eco mode Wet clean the floor and vacuum up dirt water. B Normal mode Wet clean the floor and vacuum up dirt water. C Intense mode Wet clean the floor and allow the detergent to react. D Vacuum mode Vacuum the wastewater. E Polishing mode Polishing the floor without the application of liquid. 4 A 5 A 6 A Setting the water quantity A Adjust the water quantity using the regulating button according to the dirt on the floor covering.
PAGE 3
QUICKSTART Finish operation 1 A GB B E C F Turn off the appliance A Close the regulatory button for setting the water quantity. B Release driving lever. C Lift the cleaning head. D Briefly drive forward and suck of the remaining water. E Raise the vacuum bar. The suction turbine will continue to run for 5 more seconds to suck off residual water from the vacuum bar and the vacuum hose. F Turn the program selection switch to "OFF". G Remove the Intelligent Key.
PAGE 4
QUICKSTART Finish operation A Charge battery, if required. Insert the plug of the connecting cable into the socket. 1 몇 A 2 Warning Please observe the local provisions regarding the wastewater treatment. A Take the water discharge hose from the support and lower above a suited collection device. B Rinse the wastewater reservoir with clea water or with the rinsing system for the wastewater reservoir (option). Take the water discharge hose from the support and lower above a suited collection device.
PAGE 5
몇 Warning 3 A 4 A 5 A 6 A A Clean the seals between dirt water reservoir and cover and check for tightness, replace if required. 7 A A annual B monthly daily Maintenance and care Kärcher Customer Service QUICKSTART Please observe the local provisions regarding the wastewater treatment. A Loosen the lid for emptying the fresh water - do not remove it fully. Drain water. B To rinse the fresh water reservoir, remove the cover with the seal completely and remove the fresh water filter.
PAGE 6
QUICKSTART Troubleshooting 1 A B 2 A B C GB E F 3 A B Insufficient cleaning result A Check brush for wear and tear and clean it. Check the brushes for wear (bristle length at least 10 mm), replace if required. 4 A B Insufficient water quantity A Check fresh water level, refill tank if necessary. B Unscrew the lock of the fresh water reservoir. Remove and clean the fresh water filter. Insert the filter and screw in the lock.
PAGE 7
QUICKSTART Troubleshooting 5 A B Brushes do not turn A If over-current switch in the electronics system has been triggered, turn programme selection switch to "OFF". Afterwards, set it back to the desired programme. B Check the brushes for blockage due to foreign particles, remove them if found. 6 A B Do not add detergents A Increase the water volume to activate the dosing pump. B Check level of detergent solution in the fresh water tank; refill, if required. 5.964-243.