Operating instructions
Table Of Contents
- Contents
- About this operating instructions manual
- Environmental protection
- Safety instructions
- Operation
- Open the system
- Settings
- Main switch
- Adjust compressor
- Setting dosing pumps
- Dry foam station
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Blending device (option)
- Controls
- SB MB standard
- SB MB comfort
- Normal operation
- Open the menu "customer settings"
- Select the parameter you want to set
- Set the parameter with a variable
- Setting a parameter with several variables
- Exiting the menu
- Operating times
- Lighting time
- Fixed holidays
- Non-fixed holidays
- Date / Time
- Coin value
- Programme run times
- System settings
- Setting the dosing pumps
- System
- Hot blowers
- Washing station heater
- Frost protection with lost water
- Emergency frost protection
- External thermostat
- Filling in detergents
- Manual interventions
- Sales indicator
- Frost protection
- Shutting down
- Shutdown
- Function
- Flowchart system with wet foam
- Flowchart system with dry foam
- Attachment kit disconnection from mains (optional)
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Frost protection 1-tool (option, SB- MB 2 pump Fp only)
- Frost protection 2-tool, wet foam (option, SB-MB 2 pump Fp only)
- 4. Type of water
- Internal frost protection (optional)
- External frost protection (optional)
- Washing place heating (option)
- Monitoring and safety devices
- Overflow valve of high-pressure pump
- Safety valve
- Thermostat mixing valve
- Flame monitoring
- Exhaust thermostat
- Temperature controller
- Temperature controller
- Flow monitor
- Water shortage safeguard
- Motor protection switch
- Hard water sensor
- Pressure switch for RO water shortage
- Level switch Buffer tank is full
- Level sensor pump RO on
- Level switch Buffer tank is empty
- Temperature limiter 4. type of water / warm (option)
- Technical specifications
- Maintenance and care
- Troubleshooting
- Who may remedy faults?
- Fault indication
- Faults shown in the display
- Acknowledge the faults
- Viewing the list of faults
- Viewing the event list
- Interruptions in warm water circulation
- Malfunctions of the washing station heater
- Burner malfunctions with oil-heated devices
- Burner malfunctions with gas-heated devices
- Malfunctions at coin mechanism
- Faults on high pressure pumps
- Disturbed detergent supply
- Malfunctions on the wheel cleaner/intensive foam
- Faults in the compressor
- Faults at the dry foam production (option)
- Interruptions in water preparation
- Faults on the frost protection units)
- Accessories
- Warranty
- Transport
- Storage
- Installing the unit (only for experts)
- Preparing the installation place
- Unpack the equipment
- Aligning the unit and installing it
- Assemble the installation parts
- Water connection
- Electrical connection
- Fuel pipe to the external fuel tank
- Connect the washing station heater and start it up
- Check oil level
- Filling in detergents
- Initial startup
- Turning the base exchanger on
- Start-up of the RO plant
- Check the pressure of rim cleaner (option)
- Check the function of the system
- Starting up the gas burner (option)
- Dimension drawing for CAB model
- Dimension drawing for SKID model
- Dimension drawing for SKID model with WSO upgrade kit
- EU Declaration of Conformity
- Log of high pressure testing
- 7
Adjust the air pressure reducer:
ATTENTION
Risk of damage due to acidic detergents.
Only use alkaline detergents for wheel
cleaning.
Note:
After performing the basic setup, the spray
pattern should only be changed by adjust-
ing the pressure reducer for air.
Wheel cleaner:
The uniform application onto the rims is fa-
cilitated if a suitable colouring agent is add-
ed to the rim cleaner concentrate.
1 Adjustment screw
Adjust the pressure of the micro emul-
sion as needed by turning the adjust-
ment screw.
The booster heater is supplied with partly
softened water with a water hardness of
7° dH.
For this purpose, the blending device mixes
fresh water and softened water.
1 Sampling tap
2 Outlet valve (to the booster heater)
3 Adjusting screw, fine adjustment
4 Adjusting screw, coarse adjustment
5 Inlet valve fresh water
Completely open outlet valve and inlet
valve.
Close both adjusting screws (turn in
clockwise direction).
Establish water inlet to the warm water
tank.
Open the sampling tap.
Slightly open adjusting screw coarse
adjustment.
Collect water from the sampling tap and
measure the water hardness.
Adjust the bypass valve until it is just
under 7° dH.
Set the water hardness to 7° dH using
the adjusting screw fine adjustment.
Close the sampling tap.
1 Key "1/ON"
2 Control lamp operating state
3 Display
4 LEFT key
5 RIGHT key
6 OK button
7 ESC button
1 Display
2 LEFT key
3 RIGHT key
4 OK button
5 ESC button
During normal operating mode, the control
panel display alternates between:
Day of the week, date, time, summer time
(Som)/winter time (Wint)
Operating time of the system on the current
day
Maintenance work due from customer ser-
vice (example).
If more than one maintenance procedure is
required, these will be shown in sequence.
If no maintenance procedures are required,
nothing will be shown.
Fault occurred (example).
If more than one fault is present, these will
be shown in sequence.
The number in parentheses shows the total
number of faults present.
If no faults are present, nothing will be
shown.
Note:
To acknowledge faults see "Troubleshoot-
ing"
Press OK button for more than 2 sec-
onds.
Press the RIGHT button.
Press the OK button.
The menu "customer settings" (see follow-
ing page) has been reached.
Basic setting air
Rim cleaner Intensive foam
2.5...3.0 bar 3.0 bar
Micro emulsion (option)
Blending device (option)
Controls
SB MB standard
SB MB comfort
Normal operation
Open the menu "customer settings"
9EN