Operating instructions
Table Of Contents
- Contents
- About this operating instructions manual
- Environmental protection
- Safety instructions
- Operation
- Open the system
- Settings
- Main switch
- Adjust compressor
- Setting dosing pumps
- Dry foam station
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Blending device (option)
- Controls
- SB MB standard
- SB MB comfort
- Normal operation
- Open the menu "customer settings"
- Select the parameter you want to set
- Set the parameter with a variable
- Setting a parameter with several variables
- Exiting the menu
- Operating times
- Lighting time
- Fixed holidays
- Non-fixed holidays
- Date / Time
- Coin value
- Programme run times
- System settings
- Setting the dosing pumps
- System
- Hot blowers
- Washing station heater
- Frost protection with lost water
- Emergency frost protection
- External thermostat
- Filling in detergents
- Manual interventions
- Sales indicator
- Frost protection
- Shutting down
- Shutdown
- Function
- Flowchart system with wet foam
- Flowchart system with dry foam
- Attachment kit disconnection from mains (optional)
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Frost protection 1-tool (option, SB- MB 2 pump Fp only)
- Frost protection 2-tool, wet foam (option, SB-MB 2 pump Fp only)
- 4. Type of water
- Internal frost protection (optional)
- External frost protection (optional)
- Washing place heating (option)
- Monitoring and safety devices
- Overflow valve of high-pressure pump
- Safety valve
- Thermostat mixing valve
- Flame monitoring
- Exhaust thermostat
- Temperature controller
- Temperature controller
- Flow monitor
- Water shortage safeguard
- Motor protection switch
- Hard water sensor
- Pressure switch for RO water shortage
- Level switch Buffer tank is full
- Level sensor pump RO on
- Level switch Buffer tank is empty
- Temperature limiter 4. type of water / warm (option)
- Technical specifications
- Maintenance and care
- Troubleshooting
- Who may remedy faults?
- Fault indication
- Faults shown in the display
- Acknowledge the faults
- Viewing the list of faults
- Viewing the event list
- Interruptions in warm water circulation
- Malfunctions of the washing station heater
- Burner malfunctions with oil-heated devices
- Burner malfunctions with gas-heated devices
- Malfunctions at coin mechanism
- Faults on high pressure pumps
- Disturbed detergent supply
- Malfunctions on the wheel cleaner/intensive foam
- Faults in the compressor
- Faults at the dry foam production (option)
- Interruptions in water preparation
- Faults on the frost protection units)
- Accessories
- Warranty
- Transport
- Storage
- Installing the unit (only for experts)
- Preparing the installation place
- Unpack the equipment
- Aligning the unit and installing it
- Assemble the installation parts
- Water connection
- Electrical connection
- Fuel pipe to the external fuel tank
- Connect the washing station heater and start it up
- Check oil level
- Filling in detergents
- Initial startup
- Turning the base exchanger on
- Start-up of the RO plant
- Check the pressure of rim cleaner (option)
- Check the function of the system
- Starting up the gas burner (option)
- Dimension drawing for CAB model
- Dimension drawing for SKID model
- Dimension drawing for SKID model with WSO upgrade kit
- EU Declaration of Conformity
- Log of high pressure testing
- 6
1 Ventilation lever
2 Ventilation button
3 Adjustment knob dosing volume
Pull out the adjustment knob for the
dosing volume.
Press and release the ventilation button
repeatedly and at the same time, rotate
the adjustment knob to the desired set-
ting.
Release the ventilation key.
Push in the adjustment knob for the
dosing volume.
1 Outlet water/detergent
2 Dosing valve water/detergent
3 Inlet water/detergent
4 Dosing valve air
5 Output air
6 Manometer compressed air
7 Pressure reducer air
8 Manometer water
9 Pressure reducer water
1 Dosing pump for dry foam
Open fresh water supply.
Use wash programme "Foam wash" at
a washing area.
Set pressure reducer for water to 0.25
MPa (2.5 bar).
Set the dosing pump for dry foam to
20%.
See "Adjusting dosing pumps" for pro-
cedure.
Open fresh water supply.
Remove the hose at the distribution
block water/chemicals outlet and re-
place with a 400 mm hose piece (PVC
hose 6/4).
Use wash programme "Foam wash" for
this washing area.
Set the fluid stream from the hose piece
by adjusting the dosing valve water/de-
tergent to 300 ml/min (measure with
measuring cylinder).
End wash programme "foam wash".
Remove the hose piece and reconnect
the hose to the washing area.
Repeat the setting of the dosing valves
water/chemicals for the remaining
washing areas.
Set pressure reducer for air to 0.25
MPa (2.5 bar).
Use the service tool 6.901-074.0 be-
tween the output air and the hose to the
washing area.
Use wash programme "Foam wash" for
this washing area.
Adjust the dosing valve air so that the
pressure gauge of the service tool dis-
plays 0.15 MPa (1.5 bar).
End wash programme "foam wash".
Remove the service tool and reconnect
the hose to the washing area to the dis-
tributor block air.
Repeat the setting of the dosing valves
air for the remaining washing areas.
Note:
After performing the basic setup, the con-
sistency of the foam should only be
changed by adjusting the dosing valves air.
1 Input of detergent
2 Nozzle insert
3 Suction hose for detergent
Pull off the suction hose.
Select the nozzle insert for the desired
mixing ratio:
Slide the nozzle insert all the way into
the detergent input.
Insert the suction hose.
1 Adjustment screw
Adjust the pressure via the adjustment
screw:
Basic adjustment
Detergent Position of
adjustment
knob (%)
High pressure
wash
RM 806 50
Wet foam
(Option)
RM 806 50
Dry foam (op-
tion)
RM 812 50
Hot wax RM 820 50
Top care RM 821 50
Contaminant re-
moval (option)
RM 806 50
Insect removal
(option)
RM 803 50
Dry foam station
Basic setting water
Basic setting water/chemicals
Basic setting air
Wheel cleaner/intensive foam
(option)
Nozzle colour Water/detergent
Wheel
cleaner
Intensive
foam
no nozzle 1:1 4:1
grey 1.2:1 5:1
black 2:1 6:1
beige 4:1 8:1
red 6:1 17:1
white 9:1 23:1
blue 10:1 25:1
light brown 13:1 36:1
green 21:1 48:1
orange 26:1 64:1
brown 30:1 75:1
yellow 38:1 90:1
purple 50:1 120:1
pink 100:1 240:1
Basic setting water/chemicals
Rim clean-
er
Intensive
foam
Detergent RM 801 RM 838
Nozzle colour blue yellow
Mixing ratio 10:1 90:1
Rim cleaner Intensive foam
5,5...6,5 bar 8.0...8.5 bar
8 EN