Operating instructions
Table Of Contents
- Contents
- About this operating instructions manual
- Environmental protection
- Safety instructions
- Operation
- Open the system
- Settings
- Main switch
- Adjust compressor
- Setting dosing pumps
- Dry foam station
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Blending device (option)
- Controls
- SB MB standard
- SB MB comfort
- Normal operation
- Open the menu "customer settings"
- Select the parameter you want to set
- Set the parameter with a variable
- Setting a parameter with several variables
- Exiting the menu
- Operating times
- Lighting time
- Fixed holidays
- Non-fixed holidays
- Date / Time
- Coin value
- Programme run times
- System settings
- Setting the dosing pumps
- System
- Hot blowers
- Washing station heater
- Frost protection with lost water
- Emergency frost protection
- External thermostat
- Filling in detergents
- Manual interventions
- Sales indicator
- Frost protection
- Shutting down
- Shutdown
- Function
- Flowchart system with wet foam
- Flowchart system with dry foam
- Attachment kit disconnection from mains (optional)
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Frost protection 1-tool (option, SB- MB 2 pump Fp only)
- Frost protection 2-tool, wet foam (option, SB-MB 2 pump Fp only)
- 4. Type of water
- Internal frost protection (optional)
- External frost protection (optional)
- Washing place heating (option)
- Monitoring and safety devices
- Overflow valve of high-pressure pump
- Safety valve
- Thermostat mixing valve
- Flame monitoring
- Exhaust thermostat
- Temperature controller
- Temperature controller
- Flow monitor
- Water shortage safeguard
- Motor protection switch
- Hard water sensor
- Pressure switch for RO water shortage
- Level switch Buffer tank is full
- Level sensor pump RO on
- Level switch Buffer tank is empty
- Temperature limiter 4. type of water / warm (option)
- Technical specifications
- Maintenance and care
- Troubleshooting
- Who may remedy faults?
- Fault indication
- Faults shown in the display
- Acknowledge the faults
- Viewing the list of faults
- Viewing the event list
- Interruptions in warm water circulation
- Malfunctions of the washing station heater
- Burner malfunctions with oil-heated devices
- Burner malfunctions with gas-heated devices
- Malfunctions at coin mechanism
- Faults on high pressure pumps
- Disturbed detergent supply
- Malfunctions on the wheel cleaner/intensive foam
- Faults in the compressor
- Faults at the dry foam production (option)
- Interruptions in water preparation
- Faults on the frost protection units)
- Accessories
- Warranty
- Transport
- Storage
- Installing the unit (only for experts)
- Preparing the installation place
- Unpack the equipment
- Aligning the unit and installing it
- Assemble the installation parts
- Water connection
- Electrical connection
- Fuel pipe to the external fuel tank
- Connect the washing station heater and start it up
- Check oil level
- Filling in detergents
- Initial startup
- Turning the base exchanger on
- Start-up of the RO plant
- Check the pressure of rim cleaner (option)
- Check the function of the system
- Starting up the gas burner (option)
- Dimension drawing for CAB model
- Dimension drawing for SKID model
- Dimension drawing for SKID model with WSO upgrade kit
- EU Declaration of Conformity
- Log of high pressure testing
- 47
Press the programme button and select
the function "Fill+Rinse clear" by turn-
ing the button in the direction of the ar-
row.
The control valve automatically moves
to the function "Operations". The salt
tank is filled with water.
When the water level is correct, fill the
salt tank with salt tablets according to
DIN 19604 (also see chapter on Acces-
sories).
The plant is ready for operations when
these jobs are completed. Conclude the
start-up activities by doing a soft water test.
During first start-up:
Fill the membrane with initial tap water
pressure (net it).
Rinse the memrane for 10 ... 20 min-
utes (foam formation during this proce-
dure is normal).
During fresh start-up after shutdown:
Let the rinsing run until there are no
bubbles to be seen at the throughflow
meter of the permeate.
1 Adjustment screw
Check the pressure of the detergent so-
lution.
Target value: 0.9...1.0 MPa (9...10
bars).
Adjust the pressure as needed by turn-
ing the adjustment screw.
Check burner setting.
Check all functions of the system.
Check all washing programmes on all
washing stations.
Check the plant for leaks; tighten
screws if required.
The initial startup of the gas burner must
only be performed by authorised expert
staff of the burner manufacturer.
– The device must be connected to a sep-
arate chimney.
– The exhaust system must be designed
according to the local rules and regula-
tions after consulting the concerned
chimney expert.
Type B23
Gas appliances without flow controller
where all parts of the exhaust system that
are subjected to excess pressure are free
of combustion air. The B23 installation
opens new options of connecting the appli-
ance to a traditional single-draught chim-
ney according to DIN 18160 and operating
it depending on the air conditions in the
room. The only requirement is that the
chimney must be suitable for being con-
nected to combustion devices (i.e. it has
been cleaned by inserting a stainless steel
pipe).
Refill / Clean washing
Filling the salt tank
Start-up of the RO plant
Check the pressure of rim cleaner
(option)
Check the function of the system
Starting up the gas burner (option)
Gas appliances with an exhaust
system that sucks out the combustion
air from the installation room
49EN