Operating instructions
Table Of Contents
- Contents
- About this operating instructions manual
- Environmental protection
- Safety instructions
- Operation
- Open the system
- Settings
- Main switch
- Adjust compressor
- Setting dosing pumps
- Dry foam station
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Blending device (option)
- Controls
- SB MB standard
- SB MB comfort
- Normal operation
- Open the menu "customer settings"
- Select the parameter you want to set
- Set the parameter with a variable
- Setting a parameter with several variables
- Exiting the menu
- Operating times
- Lighting time
- Fixed holidays
- Non-fixed holidays
- Date / Time
- Coin value
- Programme run times
- System settings
- Setting the dosing pumps
- System
- Hot blowers
- Washing station heater
- Frost protection with lost water
- Emergency frost protection
- External thermostat
- Filling in detergents
- Manual interventions
- Sales indicator
- Frost protection
- Shutting down
- Shutdown
- Function
- Flowchart system with wet foam
- Flowchart system with dry foam
- Attachment kit disconnection from mains (optional)
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Frost protection 1-tool (option, SB- MB 2 pump Fp only)
- Frost protection 2-tool, wet foam (option, SB-MB 2 pump Fp only)
- 4. Type of water
- Internal frost protection (optional)
- External frost protection (optional)
- Washing place heating (option)
- Monitoring and safety devices
- Overflow valve of high-pressure pump
- Safety valve
- Thermostat mixing valve
- Flame monitoring
- Exhaust thermostat
- Temperature controller
- Temperature controller
- Flow monitor
- Water shortage safeguard
- Motor protection switch
- Hard water sensor
- Pressure switch for RO water shortage
- Level switch Buffer tank is full
- Level sensor pump RO on
- Level switch Buffer tank is empty
- Temperature limiter 4. type of water / warm (option)
- Technical specifications
- Maintenance and care
- Troubleshooting
- Who may remedy faults?
- Fault indication
- Faults shown in the display
- Acknowledge the faults
- Viewing the list of faults
- Viewing the event list
- Interruptions in warm water circulation
- Malfunctions of the washing station heater
- Burner malfunctions with oil-heated devices
- Burner malfunctions with gas-heated devices
- Malfunctions at coin mechanism
- Faults on high pressure pumps
- Disturbed detergent supply
- Malfunctions on the wheel cleaner/intensive foam
- Faults in the compressor
- Faults at the dry foam production (option)
- Interruptions in water preparation
- Faults on the frost protection units)
- Accessories
- Warranty
- Transport
- Storage
- Installing the unit (only for experts)
- Preparing the installation place
- Unpack the equipment
- Aligning the unit and installing it
- Assemble the installation parts
- Water connection
- Electrical connection
- Fuel pipe to the external fuel tank
- Connect the washing station heater and start it up
- Check oil level
- Filling in detergents
- Initial startup
- Turning the base exchanger on
- Start-up of the RO plant
- Check the pressure of rim cleaner (option)
- Check the function of the system
- Starting up the gas burner (option)
- Dimension drawing for CAB model
- Dimension drawing for SKID model
- Dimension drawing for SKID model with WSO upgrade kit
- EU Declaration of Conformity
- Log of high pressure testing
- 41
1 Sieve
1 Node piece
2 Inlet high pressure with check valve
3 Throttle wheel cleaner (0.6 mm) with
check valve
4 Throttle intensive foam (1.3 mm) with
check valve
5 Inlet compressed air with check valve
6 Foam device
7 Backflow valve
8 Output high-pressure
Malfunctions on the wheel cleaner/intensive foam
Fault Possible cause Remedy By whom
Inadequate or no
flow of water/deter-
gent
Sieve in the water inlet is dirty Clean sieve. Operator
Nozzle insert in the injector clogged. Clean the nozzle insert. Operator
Throttle in node piece obstructed. Clean the parts. Operator, Cus-
tomer Service
Foam device in the hub clogged. Blow out the hub using compressed air or replace
the foam device.
Operator, Cus-
tomer Service
Faults in the compressor
Fault Possible cause Remedy By whom
Compressor
switches on and off
frequently.
Condensate level in pressure container too
high.
Drain the condensate from the pressure container
of the compressor.
Operator/Cus-
tomer Service
Faults at the dry foam production (option)
Fault Possible cause Remedy of whom
Bad dry foam qual-
ity, foam too dry or
too wet
Detergent container is empty Replace the container. Operator
Suction filter of dosing pump
plugged
Rinse the filter with warm water Operator
Water supply is too low Re-establish the water supply, set pressure reducer foam sta-
tion to 0.25 MPa (2.5 bar).
Operator
Compressor does not supply air Check the compressor
Drain the condensate from the pressure container of the com-
pressor.
Customer Service
Compressor overheated After cooling off, the compressor will automatically start operat-
ing again.
Operator
Pressure reducer foam station
contaminated
Clean pressure reducer Operator
Solenoid valve water/chemicals
does not open
Check the voltage using a magnetic field tester, clean solenoid
valve, replace if required
Operator, Custom-
er Service
Setting of dosing valves water/
chemicals or air incorrect
Perform basic setup (see chapter B Operation and Settings) Customer Service
incorrect detergent, detergent
contaminated or old
Replace detergent Operator
43EN