Operating instructions
Table Of Contents
- Contents
- About this operating instructions manual
- Environmental protection
- Safety instructions
- Operation
- Open the system
- Settings
- Main switch
- Adjust compressor
- Setting dosing pumps
- Dry foam station
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Blending device (option)
- Controls
- SB MB standard
- SB MB comfort
- Normal operation
- Open the menu "customer settings"
- Select the parameter you want to set
- Set the parameter with a variable
- Setting a parameter with several variables
- Exiting the menu
- Operating times
- Lighting time
- Fixed holidays
- Non-fixed holidays
- Date / Time
- Coin value
- Programme run times
- System settings
- Setting the dosing pumps
- System
- Hot blowers
- Washing station heater
- Frost protection with lost water
- Emergency frost protection
- External thermostat
- Filling in detergents
- Manual interventions
- Sales indicator
- Frost protection
- Shutting down
- Shutdown
- Function
- Flowchart system with wet foam
- Flowchart system with dry foam
- Attachment kit disconnection from mains (optional)
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Frost protection 1-tool (option, SB- MB 2 pump Fp only)
- Frost protection 2-tool, wet foam (option, SB-MB 2 pump Fp only)
- 4. Type of water
- Internal frost protection (optional)
- External frost protection (optional)
- Washing place heating (option)
- Monitoring and safety devices
- Overflow valve of high-pressure pump
- Safety valve
- Thermostat mixing valve
- Flame monitoring
- Exhaust thermostat
- Temperature controller
- Temperature controller
- Flow monitor
- Water shortage safeguard
- Motor protection switch
- Hard water sensor
- Pressure switch for RO water shortage
- Level switch Buffer tank is full
- Level sensor pump RO on
- Level switch Buffer tank is empty
- Temperature limiter 4. type of water / warm (option)
- Technical specifications
- Maintenance and care
- Troubleshooting
- Who may remedy faults?
- Fault indication
- Faults shown in the display
- Acknowledge the faults
- Viewing the list of faults
- Viewing the event list
- Interruptions in warm water circulation
- Malfunctions of the washing station heater
- Burner malfunctions with oil-heated devices
- Burner malfunctions with gas-heated devices
- Malfunctions at coin mechanism
- Faults on high pressure pumps
- Disturbed detergent supply
- Malfunctions on the wheel cleaner/intensive foam
- Faults in the compressor
- Faults at the dry foam production (option)
- Interruptions in water preparation
- Faults on the frost protection units)
- Accessories
- Warranty
- Transport
- Storage
- Installing the unit (only for experts)
- Preparing the installation place
- Unpack the equipment
- Aligning the unit and installing it
- Assemble the installation parts
- Water connection
- Electrical connection
- Fuel pipe to the external fuel tank
- Connect the washing station heater and start it up
- Check oil level
- Filling in detergents
- Initial startup
- Turning the base exchanger on
- Start-up of the RO plant
- Check the pressure of rim cleaner (option)
- Check the function of the system
- Starting up the gas burner (option)
- Dimension drawing for CAB model
- Dimension drawing for SKID model
- Dimension drawing for SKID model with WSO upgrade kit
- EU Declaration of Conformity
- Log of high pressure testing
- 40
Malfunctions at coin mechanism
Fault Possible cause Remedy By whom
All coin acceptors
reject all coins
Main switch is switched off. Set main switch to “1”. Operator
Incorrectly adjusted time of day or operating
times. Night operation lock active
Check the adjustments on the control. Operator
Lack of water (F 220) Check water supply. Operator
Motor protection switch of the high pressure
pumps was triggered
Reset motor protection switch.
Determine the cause if it reoccurs.
Operator
A single coin ac-
ceptor rejects all
coins
Coin acceptor dirty Clean the coin acceptor (see section „Maintenance
work“)
Operator
Overcurrent on the high pressure pump Acknowledge the fault on the control. Operator
Faults on high pressure pumps
Fault Possible cause Remedy By whom
Irregular water jet
on the hand spray
gun
High-pressure nozzle clogged Clean high-pressure nozzle. Operator
Amount of water supply is too low. Check water supply level (refer to technical data). Operator
Suction hose kinked Check suction hose. Operator
Reduced pressure
at the high-pres-
sure pump
High-pressure nozzle flushed Replace the high-pressure nozzle. Operator
Incorrect high pressure nozzle installed. Check/replace high-pressure nozzle. Operator
Amount of water supply is too low. Check water supply level (refer to technical data). Operator
Check flushing solenoid valve,swimmer valve and
water quality solenoid valve.
Customer Ser-
vice
Pressure does not
build up in the
pump
High-pressure hose to the washdown yard leak-
ing
Check the high-pressure line, replace if necessary.Operator, Cus-
tomer Service
Overflow valve misadjusted or leaking Check and repair the overflow valve. Customer Ser-
vice
The high pressure pump sucks air from the
empty detergent tank
Refill detergent. Bleed the suction line (to speed up
the bleeding process briefly squeeze the suction
hose to the pump repeatedly during operation).
Operator
High pressure
pump is knocking;
manometer is
swaying wildly
High pressure pump is sucking in air. Check suction pipes for water and detergent and
ensure that they are leak-proof.
Operator
Detergent container empty? (see above) Operator
Vibration dampener is defective Replace vibration dampener. Operator
Valve in pump head defective or contaminated.Replace defective valves. Customer Ser-
vice
The pump does not
run
Overcurrent on the high pressure pump Acknowledge the fault on the control. Operator
Disturbed detergent supply
Fault Possible cause Remedy By whom
Inadequate or no
flow of detergent
Filter or hose is blocked Clean the parts. Operator
Leaky detergent hose Replace the hose Operator
Dosing pump incorrectly adjusted or defective. Check the dosing pump and the setting. Operator, Cus-
tomer Service
Dosing pump obstructed by condensate. Drain the condensate from the pressure container
of the compressor.
Customer Ser-
vice
42 EN