Operating instructions
Table Of Contents
- Contents
- About this operating instructions manual
- Environmental protection
- Safety instructions
- Operation
- Open the system
- Settings
- Main switch
- Adjust compressor
- Setting dosing pumps
- Dry foam station
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Blending device (option)
- Controls
- SB MB standard
- SB MB comfort
- Normal operation
- Open the menu "customer settings"
- Select the parameter you want to set
- Set the parameter with a variable
- Setting a parameter with several variables
- Exiting the menu
- Operating times
- Lighting time
- Fixed holidays
- Non-fixed holidays
- Date / Time
- Coin value
- Programme run times
- System settings
- Setting the dosing pumps
- System
- Hot blowers
- Washing station heater
- Frost protection with lost water
- Emergency frost protection
- External thermostat
- Filling in detergents
- Manual interventions
- Sales indicator
- Frost protection
- Shutting down
- Shutdown
- Function
- Flowchart system with wet foam
- Flowchart system with dry foam
- Attachment kit disconnection from mains (optional)
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Frost protection 1-tool (option, SB- MB 2 pump Fp only)
- Frost protection 2-tool, wet foam (option, SB-MB 2 pump Fp only)
- 4. Type of water
- Internal frost protection (optional)
- External frost protection (optional)
- Washing place heating (option)
- Monitoring and safety devices
- Overflow valve of high-pressure pump
- Safety valve
- Thermostat mixing valve
- Flame monitoring
- Exhaust thermostat
- Temperature controller
- Temperature controller
- Flow monitor
- Water shortage safeguard
- Motor protection switch
- Hard water sensor
- Pressure switch for RO water shortage
- Level switch Buffer tank is full
- Level sensor pump RO on
- Level switch Buffer tank is empty
- Temperature limiter 4. type of water / warm (option)
- Technical specifications
- Maintenance and care
- Troubleshooting
- Who may remedy faults?
- Fault indication
- Faults shown in the display
- Acknowledge the faults
- Viewing the list of faults
- Viewing the event list
- Interruptions in warm water circulation
- Malfunctions of the washing station heater
- Burner malfunctions with oil-heated devices
- Burner malfunctions with gas-heated devices
- Malfunctions at coin mechanism
- Faults on high pressure pumps
- Disturbed detergent supply
- Malfunctions on the wheel cleaner/intensive foam
- Faults in the compressor
- Faults at the dry foam production (option)
- Interruptions in water preparation
- Faults on the frost protection units)
- Accessories
- Warranty
- Transport
- Storage
- Installing the unit (only for experts)
- Preparing the installation place
- Unpack the equipment
- Aligning the unit and installing it
- Assemble the installation parts
- Water connection
- Electrical connection
- Fuel pipe to the external fuel tank
- Connect the washing station heater and start it up
- Check oil level
- Filling in detergents
- Initial startup
- Turning the base exchanger on
- Start-up of the RO plant
- Check the pressure of rim cleaner (option)
- Check the function of the system
- Starting up the gas burner (option)
- Dimension drawing for CAB model
- Dimension drawing for SKID model
- Dimension drawing for SKID model with WSO upgrade kit
- EU Declaration of Conformity
- Log of high pressure testing
- 38
Interruptions in warm water circulation
Fault Possible cause Remedy By whom
Low water level in
the swimmer tank
for warm water
Water supply blocked Open locking tap for fresh water Operator
Sieve in the water shortage safe guard is dirty Clean or replace the filter inlay. Operator
Swimmer valve in the swimmer container for
warm water is not opening
Check swimmer valve; repair, if needed. Operator
Safeguard against water scarcity in the swimmer
container for warm water is jammed or defective
Check the water scarcity safeguard, replace if
necessary.
Operator
Hose pipe is burst or has come off Check the hose lines, replace if necessary. Operator
Pump disconnection from mains (optional) not
working
Check supply voltage.
Check pump.
Customer Ser-
vice
Water temperature
is too low / too high
Thermostat defective. Check the thermostat, replace if necessary. Customer Ser-
vice
Burner does not
start or interrupts
the heating
Flow monitor is defective Check and clean the flow monitor, replace if nec-
essary.
Customer Ser-
vice
Warm water circulation has calcium deposits Check water preparation, decalcify circuit. Customer Ser-
vice
Air in the circulation pump for warm water Deaerate the pump at the deaeration screw. Operator
Rotation direction of the circulation pump for
warm water is wrong
Check direction of rotation, modify, if required. Customer Ser-
vice
Thermostat defective. Check the thermostat, replace if necessary. Customer Ser-
vice
Protection for the circulation pump for warm water
is defective
Check the contactor, replace if necessary. Customer Ser-
vice
The motor protection switch of the circulation
pump for warm water has been triggered as the
circulation pump is blocked or the pump is defec-
tive
Check circulation pump; repair or replace if nec-
essary. Reset motor protection switch.
Customer Ser-
vice
Malfunctions of the washing station heater
Fault Possible cause Remedy By whom
Circulation pump
for washing station
heater out of order
Temperature in the warm water tank below 10 °C
(fault display "F 244").
Look for the malfunction in the warm water circuit
and fix it.
Operator/Cus-
tomer Service
40 EN