Operating instructions
Table Of Contents
- Contents
- About this operating instructions manual
- Environmental protection
- Safety instructions
- Operation
- Open the system
- Settings
- Main switch
- Adjust compressor
- Setting dosing pumps
- Dry foam station
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Blending device (option)
- Controls
- SB MB standard
- SB MB comfort
- Normal operation
- Open the menu "customer settings"
- Select the parameter you want to set
- Set the parameter with a variable
- Setting a parameter with several variables
- Exiting the menu
- Operating times
- Lighting time
- Fixed holidays
- Non-fixed holidays
- Date / Time
- Coin value
- Programme run times
- System settings
- Setting the dosing pumps
- System
- Hot blowers
- Washing station heater
- Frost protection with lost water
- Emergency frost protection
- External thermostat
- Filling in detergents
- Manual interventions
- Sales indicator
- Frost protection
- Shutting down
- Shutdown
- Function
- Flowchart system with wet foam
- Flowchart system with dry foam
- Attachment kit disconnection from mains (optional)
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Frost protection 1-tool (option, SB- MB 2 pump Fp only)
- Frost protection 2-tool, wet foam (option, SB-MB 2 pump Fp only)
- 4. Type of water
- Internal frost protection (optional)
- External frost protection (optional)
- Washing place heating (option)
- Monitoring and safety devices
- Overflow valve of high-pressure pump
- Safety valve
- Thermostat mixing valve
- Flame monitoring
- Exhaust thermostat
- Temperature controller
- Temperature controller
- Flow monitor
- Water shortage safeguard
- Motor protection switch
- Hard water sensor
- Pressure switch for RO water shortage
- Level switch Buffer tank is full
- Level sensor pump RO on
- Level switch Buffer tank is empty
- Temperature limiter 4. type of water / warm (option)
- Technical specifications
- Maintenance and care
- Troubleshooting
- Who may remedy faults?
- Fault indication
- Faults shown in the display
- Acknowledge the faults
- Viewing the list of faults
- Viewing the event list
- Interruptions in warm water circulation
- Malfunctions of the washing station heater
- Burner malfunctions with oil-heated devices
- Burner malfunctions with gas-heated devices
- Malfunctions at coin mechanism
- Faults on high pressure pumps
- Disturbed detergent supply
- Malfunctions on the wheel cleaner/intensive foam
- Faults in the compressor
- Faults at the dry foam production (option)
- Interruptions in water preparation
- Faults on the frost protection units)
- Accessories
- Warranty
- Transport
- Storage
- Installing the unit (only for experts)
- Preparing the installation place
- Unpack the equipment
- Aligning the unit and installing it
- Assemble the installation parts
- Water connection
- Electrical connection
- Fuel pipe to the external fuel tank
- Connect the washing station heater and start it up
- Check oil level
- Filling in detergents
- Initial startup
- Turning the base exchanger on
- Start-up of the RO plant
- Check the pressure of rim cleaner (option)
- Check the function of the system
- Starting up the gas burner (option)
- Dimension drawing for CAB model
- Dimension drawing for SKID model
- Dimension drawing for SKID model with WSO upgrade kit
- EU Declaration of Conformity
- Log of high pressure testing
- 37
During normal operation, active faults are
shown alternating in sequence.
The number in parentheses shows the total
number of faults present.
If a fault must be acknowledged, the dis-
play will stand still:
Fault code (F: XXX) locate the fault in
the table above and follow the instruc-
tions to eliminate the fault.
To acknowledge, press the „ESC“ key.
Press the "OK" button to confirm.
The fault is acknowledged.
Note:
If more faults should be displayed without
confirming the displayed fault, press the
key RIGHT.
The control can store a maximum of 256
occurred faults.
When the fault list is full, the oldest mes-
sage will be overwritten by the newest one.
Press the "ESC" key repeatedly until
the following display appears:
Press OK button for more than 2 sec-
onds.
Press the LEFT button.
Sum of archived fault messages
Press "OK" in order to get into the most
recently archived fault message.
1 Date of fault occurrence
2 Time of fault occurrence
3 Errow code
4 List position/number of same faults in
the fault list
Browse through the fault list using the
"LEFT" and "RIGHT" keys.
Details of the currently displayed fault
can be viewed via the "OK" key.
1 Error description
2 Errow code
3 Number of same faults in the fault list
Press the keys LEFT and RIGHT simul-
taneously.
Press "OK" in order to delete the fault
list
or
Press "ESC" in order not to delete the
fault list
The control can store a maximum of 256
occurred faults (e.g. activities in water
preparation).
When the event list is full, the oldest mes-
sage will be overwritten by the newest one.
Press the "ESC" key repeatedly until
the following display appears:
Press OK button for more than 2 sec-
onds.
Press the LEFT button.
Press the RIGHT button.
The subsequent operation is done in the
same way as with "Viewing the fault list".
F 300 No connection to electronics A7 Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 301 Outputs of the electronics A7 overloaded
F 320 No connection to electronics A8
F 321 Outputs of the electronics A8 overloaded
F 322 Current consumption of pump for micro-emulsion (intensive cleaning
complete) too high
F 323 Current consumption of pump for micro-emulsion (intensive cleaning
complete) too low
F 324 Contactor of pump for micro-emulsion (intensive cleaning complete) is
jammed
Call customer service.
F 340 No connection to electronics A9 Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 341 Outputs of electronics A9 overloaded
F 342 Power consumption of intensive foam pump too high
F 343 Power consumption of intensive foam pump too low
F 344 Contactor of intensive foam pump jammed Call customer service.
F 440 No connection to electronics A31 Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 441 Outputs of electronics A31 overloaded
Display Cause Remedy
Acknowledge the faults
Viewing the list of faults
Clearing the error memory
Viewing the event list
39EN