Operating instructions
Table Of Contents
- Contents
- About this operating instructions manual
- Environmental protection
- Safety instructions
- Operation
- Open the system
- Settings
- Main switch
- Adjust compressor
- Setting dosing pumps
- Dry foam station
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Blending device (option)
- Controls
- SB MB standard
- SB MB comfort
- Normal operation
- Open the menu "customer settings"
- Select the parameter you want to set
- Set the parameter with a variable
- Setting a parameter with several variables
- Exiting the menu
- Operating times
- Lighting time
- Fixed holidays
- Non-fixed holidays
- Date / Time
- Coin value
- Programme run times
- System settings
- Setting the dosing pumps
- System
- Hot blowers
- Washing station heater
- Frost protection with lost water
- Emergency frost protection
- External thermostat
- Filling in detergents
- Manual interventions
- Sales indicator
- Frost protection
- Shutting down
- Shutdown
- Function
- Flowchart system with wet foam
- Flowchart system with dry foam
- Attachment kit disconnection from mains (optional)
- Wheel cleaner/intensive foam (option)
- Micro emulsion (option)
- Frost protection 1-tool (option, SB- MB 2 pump Fp only)
- Frost protection 2-tool, wet foam (option, SB-MB 2 pump Fp only)
- 4. Type of water
- Internal frost protection (optional)
- External frost protection (optional)
- Washing place heating (option)
- Monitoring and safety devices
- Overflow valve of high-pressure pump
- Safety valve
- Thermostat mixing valve
- Flame monitoring
- Exhaust thermostat
- Temperature controller
- Temperature controller
- Flow monitor
- Water shortage safeguard
- Motor protection switch
- Hard water sensor
- Pressure switch for RO water shortage
- Level switch Buffer tank is full
- Level sensor pump RO on
- Level switch Buffer tank is empty
- Temperature limiter 4. type of water / warm (option)
- Technical specifications
- Maintenance and care
- Troubleshooting
- Who may remedy faults?
- Fault indication
- Faults shown in the display
- Acknowledge the faults
- Viewing the list of faults
- Viewing the event list
- Interruptions in warm water circulation
- Malfunctions of the washing station heater
- Burner malfunctions with oil-heated devices
- Burner malfunctions with gas-heated devices
- Malfunctions at coin mechanism
- Faults on high pressure pumps
- Disturbed detergent supply
- Malfunctions on the wheel cleaner/intensive foam
- Faults in the compressor
- Faults at the dry foam production (option)
- Interruptions in water preparation
- Faults on the frost protection units)
- Accessories
- Warranty
- Transport
- Storage
- Installing the unit (only for experts)
- Preparing the installation place
- Unpack the equipment
- Aligning the unit and installing it
- Assemble the installation parts
- Water connection
- Electrical connection
- Fuel pipe to the external fuel tank
- Connect the washing station heater and start it up
- Check oil level
- Filling in detergents
- Initial startup
- Turning the base exchanger on
- Start-up of the RO plant
- Check the pressure of rim cleaner (option)
- Check the function of the system
- Starting up the gas burner (option)
- Dimension drawing for CAB model
- Dimension drawing for SKID model
- Dimension drawing for SKID model with WSO upgrade kit
- EU Declaration of Conformity
- Log of high pressure testing
- 31
After 40 op-
erating hours
or once a
week
opinion Tightness of systemCheck pumps and pipes for leaks. Inform Customer Service if there is
oil under the high pressure pump, if more than 3 drops of water drop
out of the high pressure pump when the pump is running.
Operator
opinion Oil condition Milky oil indicates that it contains water. Inform Customer Service. Operator
opinion Check oil level in
the high pressure
pumps
The oil level must lie between the MIN and MAX markings; else refill. Operator
opinion Detergent hoses
with filter
Visual inspection of the high-pressure jet whether it contains detergent.
Clean the filter if necessary.
Operator
opinion Entire plant Check the functions of all wash programs. Operator
opinion Salt stock in the salt
tank
Is the salt level above the water level? If required, top up softening
salts.
Operator
opinion Residual hardness
of softened water
Take warm water from the swimmer tank and determine its residual
hardness using test set B (order no. 6.768-003). Target value: below 3
°dH.
Operator
check if the chlo-
rine content in the
fresh water ex-
ceeds 0.3 mg/l
Residual chlorine
content after acti-
vated carbon filter
Take a water sample between the activated carbon filter and the RO-
membrane. Determine residual chlorine content. If the residual chlorine
content of the water sample exceeds 0.1 mg/l renew activated carbon
filter.
Operator
switch on briefly Washing station
heater
Activate on the frost protection pump as described in Chapter "Manual
procedures".
Operator
Clean the filter Casing exterior
(stainless steel and
plastic
Mix detergent "Wash hall and tile cleaner RM 841“ at 10%, apply to the
surfaces, let it soak for 2 to 3 minutes, do not allow to dry. Rinse thor-
oughly with high pressure jet after the soak time.
Operator
Mix detergent "Wash hall and tile cleaner RM 841“ at 20 %, apply to the
surfaces, let it soak for 2 to 3 minutes. After the soak-in time, clean the
surfaces with a moist pad or microfibre cloth and then rinse thoroughly
by a high pressure jet. If desired, larger areas can be cleaned using a
rubber edged "Squeegee".
Operator
Splash guard tar-
paulins
Mix detergent "Wash hall and tile cleaner RM 841“ at 10%, apply to the
surfaces, let it soak for 2 to 3 minutes, do not allow to dry. Rinse thor-
oughly with high pressure jet after the soak time.
ATTENTION
Risk of damage. Do not clean splash guard tarpaulins with solvents or
solvent-containing detergents.
Operator
Care Casing exterior
(stainless steel)
Take care of the stainless steel casing using steel cleaner. Operator
weekly in
case of frost
opinion Heating ABS heat-
ing oil tank (option)
With temperatures below 3°C, check if the trace heating of the heating
oil line between the heating oil tank and SB MB is warm.
Operator
Once, 1
month after
start-up
Exchange filter Fine filter WSO Close the locking valve for fresh water (building site), unscrew the filter
cup, replace the filter inlay, insert the new filter inlay and the filter cup
back into place, open locking valve for fresh water.
Operator
After 80 op-
erating hours
or once eve-
ry two weeks
Cleaning and pre-
serving
All stainless steel
parts of the case
Remove dirt and deposits. Preserve the parts using special steel care
oil.
Operator
Time Activity Assembly affectedPerformance By whom
33EN