ECO! T11 Bp LINER Cleaning Cart with Vacuum Operating Instructions (ENG) MODELS: 1.013-100.0 1.013-101.0 1.013-103.
Machine Data Label Overview The ECO! T11 Bp Liner is a multi-functional cleaning machine intended for commercial use. Warranty Registration Thank you for purchasing a Kärcher North America product. Warranty registration is quick and easy. Your registration will allow us to serve you better over the lifetime of the product. To register your product go to : http://warranty.karcherna.
Table of Contents Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How To Use This Manual . . . . . . . . . . . . . . . . . . . . . 4 Safety IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . 5 HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . . 7 Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How To Use This Manual The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. This manual contains the following sections: • • • • How to Use This Manual Safety Operations Maintenance The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
Safety IMPORTANT SAFETY INSTRUCTIONS When using this machine, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: • • • • • • • • • • • • • • • • • • • • • • Connect to a properly grounded outlet. See Grounding Instructions. Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or service. Use only in enclosed areas.
Safety CONSIGNES DE SÉCURITÉ IMPORTANTES Lors de l'utilisation de cette machine, des précautions de base doivent toujours être prises, y compris les précautions suivantes : LIRE TOUTES LES INSTRUCTIONS AVANT D'UTILISER CETTE MACHINE. Pour réduire le risque d'incendie, d'électrocution ou de blessure : • • • • • • • • • • • • • • • • • • • • • • Raccordez l'appareil à une prise adéquatement reliée à la terre. Voir les Consignes de mise à la terre.
Safety HAZARD INTENSITY LEVEL The following symbols are used throughout this guide as indicated in their descriptions: There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death. CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
Safety Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions : DEGRÉS DE RISQUES EN CAS DE DANGER Il existe trois degrés de risques identifiés par les termes signalétiques -AVERTISSEMENT et ATTENTION et POUR VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante: AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou entraîner la mort.
Safety Safety Labels NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. EMPLACEMENT DE L'ÉTIQUETTE DE SÉCURITÉ REMARQUE : Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine. Si, à tout moment, les étiquettes deviennent illisibles, contactez votre représentant autorisé pour un remplacement rapid 8.641-103.0 LABEL, WARNING, VACUUM 8.640-248.
Safety Electrical . In the USA this machine operates on a standard 15 amp 115 volt A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motor and electrical components.
Notes 86405760 ECO! T11 Bp LINER 11
Operations Technical Specifications ITEM Electrical Electric Vacuum Motor Water Lift Vacuum Bag Capacity Air Flow Power Cable Front (2) Rear (2) 12 DIMENSION/CAPACITY 115 VAC, Internally Powered with 36 VDC (3 - 12V Batteries) 36 VDC, 500W 65 Inches 10 Qt 85 CFM 20ft (7.62m) 18 gauge Wheels 5in Dia. (12.7cm) x 1.5 12in Dia. (30.48cm) x 1.
Operations ITEM Weight Length Height Width MEASURE 180 lbs (82kg) for 1.013-100.0 194 lbs (88 kg) for 1.013-101.0 46 in (1168mm) 43 in (1092mm 25in (635mm) Width Height Length This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Operations How the Machine Works The ECO! T11 Bp Liner is a multi-functional cleaning machine intended for commercial use. It can be used as a mobile station that can be placed in a convenient area to provide vacuum cleaning of floors and surfaces with a variety of cleaning attachments. It also provides garbage collection and convenient storage of utensils and supplies for general surface cleaning. The machine's primary systems are: • • • • 14 High-efficiency vacuum with on-board 20 ft.
Operations 6 5 2 3 8 4 11 1 7 10 9 Components/Controls 1. Control Panel 2. Vacuum Chamber Lid 3. Trash Container 4. Vacuum Floor Tool 5. Telescoping Wand 6. Vacuum Handle 7. On/Off Switch 8. Battery Charger Cord 9. Battery Status Indicator LED 10. Bag Full Indicator LED 11.
Operations Control Panel The on/off switch is located on the upper right side of the control panel There are two indicator lights on the control panel: 1 2 1. Bag Full Indicator LED: Vacuum Motor Off On Bag Almost Full Bag Full LED Off Solid Green Solid red. Machine shuts down, stays solid red for 10 seconds. 2. Battery Indicator LED: NOTE: If the battery is dead, the vacuum motor will not turn on until the charger is plugged in.
Operations Equipment Set Up Vacuum Bags FOR SAFETY: Turn off vacuum before changing filter bags. Charging the Machine Ensure that the machine has a fully charged battery pack. Pull the coiled extension cord from its storage box, plug the cord termination into a grounded wall outlet. When the machine is first plugged in, the control panel battery status light will double-flash green. This indicates that the battery charger is connected to external power and is properly charging the batteries.
Maintenance Daily Maintenance Before making any repairs or adjustments to the machine, disconnect the power cord from the electrical source. Periodically inspect all hoses, electrical cables and connections on your machine. Frayed or cracked hoses should be repaired or replaced to eliminate vacuum pressure loss. The electrical cable must be well insulated. If the cable insulation is broken or frayed, repair or replace immediately. Don't take chances with electrical fire or shock.
Maintenance Troubleshooting Blink Code 1 2 3 4 5 6 7 8 9 10 11 12 Battery Indicator LED Error Codes Error Condition Vacuum Over Current Vacuum > 15A Vacuum Under Current Vacuum < 8A Charger Over Current, Vacuum On Charger > 19A Charger Over Current, Vacuum Off Charger > 8A Charger Under Current, Vacuum On Charger < 15A and Battery <39V Bag Full Sensor Open Circuit Bag Full Sensor Short Circuit Stalled Vacuum Motor during Startup Vacuum Motor Over Temp. Temp. >203°F (95°C) Machine Over Temp. Temp.
Maintenance Service Schedule MAINTENANCE DAILY Check bag and replace if necessary Check hoses for wear, blockages, or damage Check major gaskets for leakage Check brush-should be clean with no lint or strings attached Store cord in pocket Check hoses for cracks or holes Check all cords and handles for damage or cracks; replace as necessary Inspect and replace all filters including exhaust, intake, and microfilters Check all gaskets for wear and leakage Check vacuum motor carbon brushes Check for arcing a
Maintenance Vacuum Motor Replacement Vacuum Motor Carbon Brushes Replacement End Cap Only qualified maintenance personnel are to perform the following repairs. Seul le personnel d'entretien qualifié peut effectuer des réparations Carbon Brushes WARNING: The ground wire must be attached for safe operation. See wiring diagram. If armature commutator is grooved, extremely pitted or not concentric, the motor will need to be replaced or sent to a qualified service center. 1.
Maintenance Battery Maintenance Use AGM or Gel Batteries Only. Use of other batteries may result in operator injury. Utilisez uniquement des batteries AGM ou Gel. L’utilisation d’autres batteries peut blesser l’opérateur. Only qualified maintenance personnel are to perform the following repairs. Seul le personnel d'entretien qualifié peut effectuer des réparations Batteries The batteries provide the power to operate the machine.
Maintenance Use AGM or Gel Batteries Only. Use of other batteries may result in operator injury. Utilisez uniquement des batteries AGM ou Gel. L’utilisation d’autres batteries peut blesser l’opérateur. Wear eye protection and protective clothing when working with batteries. Portez des lunettes de protection et des vêtements de protection lorsque vous travaillez avec des batteries. Charge batteries in a well ventilated area. Chargez les batteries dans un endroit bien ventilé.
Maintenance Charging Batteries Use AGM or Gel Batteries Only. Use of other batteries may result in operator injury. Utilisez uniquement des batteries AGM ou Gel. L’utilisation d’autres batteries peut blesser l’opérateur. Only qualified maintenance personnel are to perform the following repairs. Seul le personnel d'entretien qualifié peut effectuer des réparations Not all batteries require maintenance. AGM and Gel batteries are maintenance free.
Maintenance Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Les batteries émettent du gaz hydrogène. Une explosion ou un incendie peut en résulter. Maintenez les étincelles et les flammes nues à l’écart. Gardez les carters ouverts lors du chargement. Charging Batteries (continued) 1. This machine includes an on-board charger. 2. The battery status indicator LED will display a color and flashing patterns during machine usage.
Maintenance Batteries Use AGM or Gel Batteries Only. Use of other batteries may result in operator injury. Utilisez uniquement des batteries AGM ou Gel. L’utilisation d’autres batteries peut blesser l’opérateur. Only qualified maintenance personnel are to perform the following repairs. Seul le personnel d'entretien qualifié peut effectuer des réparations. Not all batteries require maintenance. AGM and Gel batteries are maintenance free. Do not attempt to remove sealed caps from AGM or Gel batteries.
Maintenance FOR SAFETY: Before leaving or servicing the machine; stop on level surface and turn off machine. Changing Batteries 1. Open the control panel. 2. Disconnect battery pack from machine. 3. Use the proper size open end wrench to disconnect main ground wire first and secure cable terminal away from batteries. 4. Disconnect main positive lead and secure cable terminals away from batteries. 5. Remove bolt from Battery Strap. 6. Loosen both terminals on each jumper cable and remove one at a time. 7.
Maintenance Delta Q IC650 Charger Operating Instructions Only qualified maintenance personnel are to perform the following repairs. Seul le personnel d'entretien qualifié peut effectuer des réparations - The charger may become hot during charging. Use hand protection to safely handle the charger during charging. - Extension cords must be a 3-wire cord no longer than 30m (100') at 10 AWG or 7.
Maintenance Selecting a Charge Profile 1. Disconnect AC input from the charger, or from the wall outlet. Wait 30 seconds for the input relay to open. Figure 1: Disconnect AC input from the charger. *Process will time out and profile will remain unchanged if there is 15 seconds of inactivity, a profile number is allowed to display three times, or if AC power is cycled. 4.
Maintenance Configuring the IC650 Charger Using a USB Flash Drive Only qualified maintenance personnel are to perform the following repairs. Seul le personnel d'entretien qualifié peut effectuer des réparations Using the Delta Q software, USB storage drives can be pre-programmed to certain charger configuration. To use the USB port, follow these steps: 1. Insert the USB flash drive at any time, except during a charge cycle. Stop the charge cycle by removing AC power or the DC connection to the batteries.
Maintenance Confirming a Software Update After using a USB flash drive to update the charger firmware, the update can be confirmed by reviewing the .txt file written to the flash drive by the charger. It will be located in the folder labelled ‘syslog’ (e.g. F:\CHARGER\RESP\serialno\syslog\00000000.txt). Open this file using a text editing program such as Notepad or Microsoft Word.
Suggested Spare Parts 8.640-361.0 HOSE ASSEMBLY 8.640-204.0 WAND 8.600-351.0 MOTOR FILTER 8.683-043.0 CARBON BRUSH FOR 24/36V C-MOTOR 8.634-487.0 DUST BRUSH 6.907-410.0 FLOOR ATTACHMENT 6.903-403.0 CREVICE NOZZLE 8.600-166.0 SHAFT HUBCAP 8.630-979.0 WHEEL 8.630-007.0 HUBCAP 8.619-885.0 REPLACEMENT PAPER BAGS (PKG. OF 10) NOT SHOWN 8.640-211.
Notes 86405760 ECO! T11 Bp LINER 33
Table of contents ECO! T11 BP LINER 1 BATTERIES 2 BODY 3 CHARGER 4 LABELS 5 VACUUM 6 WAND 7 WHEELS 8 TRASH ACCESSORIES 100 ECO! CART SERIAL NUMBER Valid on 27.09.
ECO! T11 BP LINER POS Description Quantity Unit 1 BATTERIES 1.000 ST 2 BODY 1.000 ST 3 CHARGER 1.000 ST 4 LABELS 1.000 ST 5 VACUUM 1.000 ST 6 WAND 1.000 ST 7 WHEELS 1.000 ST 8 TRASH ACCESSORIES 1.000 ST 100 ECO! CART SERIAL NUMBER 1.000 ST Valid on 27.09.
1 BATTERIES Valid on 27.09.
1 BATTERIES POS Article no. Description Quantity Unit 1 8.640-858.0 Screw 10-32 X 1 TPNHMS SS BLK ZNPLT 1.000 ST 2 8.640-395.0 Bracket battery strap 2.000 ST 3 8.640-240.0 Bracket battery harness 1.000 ST 4 8.640-214.0 BREAKER, 30A, 250VAC, 50VDC 1.000 ST 5 8.637-463.0 Battery 12V 33AH 3.000 ST 6 8.636-177.0 WASHER, 1/4 FLT SS 3.000 ST 7 8.636-152.0 CLIP, CABLE ENTRY 2.000 ST 8 8.627-695.0 SCREW, 1/4-20 X .75 CARR SS 1.000 ST 9 8.627-382.0 SCREW, 1/4-20 X 1.
2 BODY Valid on 27.09.
2 BODY POS Article no. Description Quantity Unit 1 8.640-279.0 Nut 8-32 HEX NYLOCK ST BLKZINC 4.000 ST 2 8.640-278.0 Screw 8-32 X.75 TPNHMS SS BLK ZNPLT 4.000 ST 3 8.640-276.0 Screw 5/16-18 X 1/2 TTRHMS SS BLK ZNPLT 6.000 ST 4 8.640-186.0 GASKET, .188 x .37 x 61 1.000 ST 5 8.640-185.0 Bracket trash home base 1.000 ST 6 8.640-184.0 Bracket wand shelf 1.000 ST 7 8.640-164.0 CART, TRIMMED, GRY, T11BPB 1.000 ST 8 8.600-299.0 CLIP, C 1 1/2" PLASTIC 1.000 ST 9 6.
3 CHARGER Valid on 27.09.
3 CHARGER POS Article no. Description Quantity Unit 1 8.640-858.0 Screw 10-32 X 1 TPNHMS SS BLK ZNPLT 7.000 ST 2 8.600-581.0 NUT, 1/4-20 HEX NYLOCK SS 11.000 ST 3 8.640-222.0 Clamp 1/4 cushioned .265 MTG 1.000 ST 4 8.640-203.0 Cord set 18/3 SVEO coil 20 foot 1.000 ST 5 8.640-202.0 Bezel LED 2.000 ST 6 8.640-201.0 Switch SPST 2-POS MOM ROCKER 1.000 ST 7 8.640-193.0 Bracket cord housing 1.000 ST 8 8.640-191.0 Panel control T11BPB 1.000 ST 9 8.639-530.
4 LABELS Valid on 27.09.
4 LABELS POS Article no. Description Quantity Unit 1 8.640-275.0 Label battery cabling 1.000 ST 2 8.640-236.0 Label control panel T11BPB 1.000 ST 3 8.640-238.0 Label cord 1.000 ST 4 8.640-237.0 Label side 2.000 ST 5 8.633-500.0 Label AKW domed logo 1.000 ST 6 8.641-535.0 LABEL, CRI, BRONZE 1.000 ST Valid on 27.09.
5 VACUUM Valid on 27.09.
5 VACUUM POS Article no. Description Quantity Unit 1 8.640-935.0 GASKET, HARNESS SEAL 1.000 ST 2 8.637-188.0 SCREW, 1/4-20 x .75 THUMB SS 5.000 ST 3 8.640-904.0 Screw M8-1.25 X 10 PHPNHMS SS 1.000 ST 4 8.640-858.0 Screw 10-32 X 1 TPNHMS SS BLK ZNPLT 2.000 ST 5 8.640-414.0 Gasket muffler bracket 1.000 ST 6 8.640-388.0 Bracket muffler hose 1.000 ST 7 8.640-374.0 BRKT, VAC EXHAUST, WELDMENT 1.000 ST 8 8.640-358.0 Bracket vac motor mount upper 1.000 ST 9 8.640-357.
6 WAND Valid on 27.09.
6 WAND POS Article no. Description Quantity Unit 1 8.640-361.0 Assembly handle hose 20 FT 1.000 ST 2 8.640-204.0 WAND, TELESCOPIC, ALUM 1.000 ST 3 8.634-487.0 BRUSH, DUST 1.000 ST 4 6.907-410.0 Combination nozzle packaged basalt grey 1.000 ST 5 6.903-403.0 Crevice nozzle DN32 1.000 ST Valid on 27.09.
7 WHEELS Valid on 27.09.
7 WHEELS POS Article no. Description Quantity Unit 1 8.640-877.0 Strap static .25T X 1.12W X 8L 1.000 ST 2 8.640-276.0 Screw 5/16-18 X 1/2 TTRHMS SS BLK ZNPLT 11.000 ST 3 8.640-181.0 Bracket rear wheel mount 1.000 ST 4 8.640-180.0 CASTER, 5" DIA SWIVEL 2.000 ST 5 8.640-179.0 Plate caster mount 1.000 ST 7 8.630-979.0 Wheel 12" x 2.25" 2.000 ST 8 8.630-007.0 HUBCAP, 9.75" WHEEL, BLACK 2.000 ST 11 9.802-776.0 NUT, 5/16-18, ESNA 8.000 ST 12 8.601-073.
8 TRASH ACCESSORIES Valid on 27.09.
8 TRASH ACCESSORIES POS Description Quantity Unit 1 POUCH, CART SUPPLIES 1.000 ST 2 CAN, TRASH, 40 GAL, BLK 1.000 ST Valid on 27.09.
100 ECO! CART SERIAL NUMBER POS Description Quantity Unit 10 SERIAL NUMBER PAGE 1.000 ST Valid on 27.09.2018 Powered by TCPDF (www.tcpdf.
