Operating instructions

- 8
The factory settings of all parameters are
restored.
Parameters that are adjusted with the grey
Intelligent Key, are kept until another set-
ting is selected.
 Turn the program selection switch to
the desired cleaning program.
 Press the info button - the first adjusta-
ble parameter is displayed.
 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
 Select the next parameter by turning
the Info button.
 After all desired parameters have been
modified, turn the info button until "Exit
menu" is displayed.
 Press the info button - you will exit the
menu.
 DANGER
Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients of max. 10%. Drive slowly.
몇 CAUTION
Risk of personal injury or damage! Mind the
weight of the appliance during transport.
 When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
 Remove brushes from the brush head.
몇 CAUTION
Risk of personal injury or damage! Consid-
er the weight of the appliance when storing
it.
 This appliance must only be stored in
interior rooms.
 Select the storage site for the appliance
taking into consideration the permissi-
ble total weight of the appliance in order
not to impact its stability.
 DANGER
Risk of injury!
During cleaning or maintenance or when
replacing parts or upon changing the de-
vice to another function, the positive termi-
nal of the battery must be disconnected
and the mains plug of the charger must be
unplugged.
 Drain and dispose of the dirt water and
the residual fresh water.
몇 CAUTION
Risk of injury due to overrun of the suction
turbine.
Suction turbine will continue to run for a
while after switch-off. Carry out mainte-
nance tasks only after the suction turbine
has come to a halt.
ATTENTION
Risk of damage. Do not sluice the appli-
ance with water and do not use aggressive
detergents.
 Drain off dirt water.
 Rinse the waste water tank with clear
water.
 Clean protective turbine strainer.
 Only with R cleaning head Remove bulk
waste container and empty it.
 Clean the outside of the appliance with
a damp cloth which has been soaked in
mild detergent.
 Clean the vacuum lips and the wiping
lips, check for wear and replace if re-
quired.
 Check the brushes for wear, replace if
required.
 Do not close the lids of the fresh water
and waste water tanks so that the tanks
can dry up.
 Charge the battery:
If the charging state of the battery is un-
der 50%, charge the battery fully and
without interruption.
If the charging state of the battery is
over 50%, only recharge the battery if
the entire operation duration will be re-
quired when next used.
 When used regularly, charge the bat-
tery fully and without interruption at
least once a week.
 During long operating pauses: Carry
out refill charging for the battery.
 Check battery poles for oxidation, brush
off if necessary. Ensure firm seating of
the connection cable.
 Clean the seals between waste water
tank and cover and check for tightness,
replace if required.
 Check the acid density of the cells if the
batteries are not maintenance-free bat-
teries.
 Clean the brush tunnel (only R cleaning
head)
 Remove the water distribution strip from
the cleaning head and clean water ca-
nal (only R cleaning head).
 For long periods of disuse, only turn the
device off when the battery is fully
charged. Fully recharge the battery at
least every month.
 Have the prescribed inspection carried
out by the customer service.
When a maintenance task indicated in the
display has been performed, the relevant
maintenance counter must be reset after-
wards.
 Plug in the Intelligent Key.
 Release emergency-stop button by
turning.
 Set programme selector switch to trans-
port run.
 Press Info button.
 Turn the info button until "Maintenance
counter" is displayed.
 Press Info button.
The counter readings are displayed.
 Press Info button.
"Delete counter" is indicated.
 Turn the info button until the counter to
be deleted is highlighted.
 Press Info button.
 Select "YES" by turning the info button.
 Press Info button.
The counter is deleted.
Note:
The service counter can only be reset by
the customer service.
The service counter indicates the time until
the next service by the customer service is
due.
To ensure a reliable operation of the appli-
ance maintenance contracts can be con-
cluded with the competent Kärcher sales
office.
 Open the cover of the waste water tank.
Factory setting
Cleaning Programs
Transport
With mounted D cleaning head
Storage
Care and maintenance
Maintenance schedule
After the work
Weekly
Monthly
Yearly
Reset the counter
Maintenance contract
Maintenance Works
Cleaning the protective turbine strainer
23EN