MCT244 2.
MCT244 TRANSCEIVER INDEX DESCRIPTION ........................................................................... 2 OPERATION .............................................................................. 2 INSTALLATION ......................................................................... 3 BEFORE APPLYING POWER! ...................................................... 4 TROUBLESHOOTING ................................................................. 4 INDUSTRY CANADA STATEMENTS .........................
MCT244 TRANSCEIVER DESCRIPTION amplifier, a modulator and a receiver The MCT244 is a direct sequence spread spectrum transceiver module designed to free use in The transceiver. via The data is microcontroller is responsible for the control of the entire The MCT244 is not designed for antenna not be used The DC regulator which generates a to constant 1.8 VDC for the digital with circuitry. The RF section runs on any other transmitter. the 3.3V supply. OPERATION MCT244 communication.
MCT244 TRANSCEIVER The receivers are matched to simultaneously with any the transmitters to use the same other channel transmitter, except signals. accordance with INSTALLATION multi transmitter product as the 1) Solder transmitter’s the MCT244 D) The operate as requirement. host’s Application Requirements: current with draw must all persons, not In User the Manual parts the modules. b. The radio should in not “Instructions To The User” section. be c.
MCT244 TRANSCEIVER for use in Mobile only configurations which used the antennas for transmitter in must this be installed to provide a separation distance of at least 20cm from all person and not be colocated with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter product procedures.” BEFORE POWER! APPLYING Check power and ground for proper polarity. Read the rest of this manual. parts in the MCT244 Transceiver.
MCT244 TRANSCEIVER There are no user-serviceable parts inside the transmitter or the receiver. Return the units for service. PARTS LIST PART NUMBER DESCRIPTION 021531A MCT244 RADIO TRANSCEIVER – WIRE ANTENNA 021532A MCT244 RADIO TRANSCEIVER – RPSMA ANTENNA There are no user-serviceable parts inside the transmitter or the receiver. Return the units for service. The information, specifications, and illustrations in this manual are those in effect at the time of printing.
MCT244 TRANSCEIVER Pinout Pin 1 2 3 4 5 6 Function GND Not Used GND Not Used Not Used NC Pin 7 8 9 10 11 12 Function NC Not Used Not Used NC RXD TXD 6 Pin 13 14 15 16 17 18 Function NC NC NC NC VIN 3.
MCT244 TRANSCEIVER TRANSCEIVER Power supply ........................................................................... 3.3VDC Operating temperature - Radio....................................... -20˚C to +55˚C Storage temperature .................................................. -40˚C to +100˚C RF Frequency ............................................................... 2.405-2.48 GHz Antenna Manufacturer …………………………………………………………….. Kar-Tech, Inc. Antenna Model…………………………………………………………………………………..
MCT244 TRANSCEIVER INSTRUCTION TO THE USER This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
MCT244 TRANSCEIVER be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.
MCT244 TRANSCEIVER INDUSTRY CANADA STATEMENTS This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
MCT244 TRANSCEIVER OEM Responsibilities to comply with FCC and Industry Canada Regulations This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada .
MCT244 TRANSCEIVER 1. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. 2. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada .
