Multi-Channel ANEMOMASTER for Windows Instruction Manual KANOMAX JAPAN INC.
Contents Caution...................................................................................................................................................................................... 2 Transcription of this Manual................................................................................................................................................ 2 1. Components of this System............................................................................................................
Caution 1.Copyrights of this software are property of Kanomax Japan Inc. 2.Partly or wholly duplicating and using this software and user manual without permission is not allowed. 3.Only one computer is allowed to install and use per a set of this software you purchased. 4.Please understand that an influence on your computer after managing this software or using user manual is not our responsibility. 5.Specification of this software and contents of user manual can be revised without pre-notice.
1. Components of this System . 5 units of ANEMOMASTER Corresponds to 4 modules of (MAX) can be connected V, VT, VTH, SP Install Multi-channel ANEMOMASTER software for Windows Pic1 Components of system 2. Operation Environment ・Computer : Computer loaded with Pentium CPU ・OS : Windows 95 or Windows 98 ・Memory : More than 8 MB ・Hard disk : Need more than 5 MB for installation ・Display :More than 640×480 pic. Corresponds to Windows 95 or Windows 98 (Recommendation: 800×600 pic.
3. Functional Specification ITEM CONTENTS Model No. Module Numbers of ANEMOMASTER Channel Nos to measure Probe positioning Measurement mode 1550, 1560, 1500 V, VT, VTH, SP 5 units (maximum) can be connected. Data mode Average value mode, Instant mode Interval of measurement 0.1~6553.5seconds, you can set up by 0.1 second unit 65535 times MAX. Repetition time MAX. 320CH (in case of V module) CH Nos depend on module. Optional position in 3 dimension of rectangular coordinates.
4. Outline of Software 4.1 Components of Software 1) Components of Software This software consists of following files. Items Set up program File name Setup.exe Main part of soft ware MAVIEW.exe Comment Program to set up “Multi-channel ANEMOMASTER software for Windows”. Set up program checks PC environment and install needed files automatically. Main part of “Multi-channel ANEMOMASTER software for Windows” (executable file). Bit Map picture data of ANEMOMASTER . SetAmA.bmp SetAmB.bmp *.
2) Data File List Basic data file ・File name:###.KAM ・System :Binary system ・Contents :File info, system parameter, RS232C parameter, Measure parameter, Measured time series data, Statistic calculation result *This program does data save, handle data, indication, on the basis of this data file. Parameter file ・File name:###_P.TXT ・System :Text system Contents :System parameter, RS232C parameter, Measured parameter * Formed with basic data file.
4.2 Set up and Delete of Multi-channel ANEMOMASTER Software 1) Set up (install ) of Multi-channel ANEMOMASTER When you execute “Setup.exe” , set up program will check PC environment and install needed files automatically. Default directory of install destination is “ C:¥Program – File¥MAVIEW “ . If you want to change destination, click “ change directory” button and change directory which is destination of install before start setting up.
2) Delete (uninstall) of Multi-channel ANEMOMASTER 削除 : You can delete multi-channel ANEMOMASTER soft by “ Add/Remove Programs” of “Control Panel”. Pic.
4.3 Displays This program adopted Multi-document interface ( MDI ). This program opens basic data file ( *.KMA ) and indicate set up data and measurement data which are stored in files. More than two basic data files can not be opened simultaneously. Structure of display is as follows. (Figures in parentheses shows numbers of windows which can be indicated simultaneously.) Index screen [Pic. 4] Windows Module set up window (1) [Pic. 6, 17] Probe set up window (1) [Pic.
5. Operation Order ① Start up program Start up operation (Exe.file : MAVIEW.EXE ) Pic. 4 Index screen ② Initial screen New draw up of data file Pic.
③ Module set up Pic. 6 Module set up screen ④ Probe set up Pic. 7 Probe set up screen ⑤ Open data indication windows Pic.
⑥ Set up RS232C Pic. 9 RS232C set up dialogue box ⑦ Measurement parameter set up Pic. 10 Measurement menu ⑧ Start measuring *Click start measurement button of measurement parameter set up dialogue box Pic. 11 Measurement parameter set up dialogue box ⑨ Take in data Pic.
measurement ) ⑩ Data display after finished data take-in ※ Possible to indicate previous measurement data again. Pic. 13 Data display after finished data take-in ⑪ Data storage Pic 14 File menu Pic. 15 Name and save file ⑫ Finish program : Select “Close” of file menu and finish the program.
6. Operation Explanation 6. 1 Structure of Display Name of program Name of file Title bar Menu bar Tool bar Operation Area Status bar Common message File condition Data condition Pic.
6.2 Module Set up Click when finished module set up 2’nd U2 Set up visually 1’st U1 When click and select main body, module addition to module box become possible Set up by table Combo box:Register, Module box : Click change, delete icon ANEMOMASTER and register main body or module of main body Combo box : Register, change, delete of module ( delete : NULL ) Pic. 17 Module set up window You can add module and main part by clicking module icon or main part of ANEMOMASTER in module box.
6.3 Probe Set up Select items to input Key input Select unit You can change “ * ” and of position “ Blank “ by click Pic. 18 Probe set up window z Items to input Connect condition (USE) : 〇 : Connect, × : Disconnect ( change by click or key ) Probe No. : Value or Alphabet of 4 digits ( Key input ) Probe comment : Characters of 10 digits ( Key input ) Probe position : Set up by key Input format is as follows Unit of mm : XXXX Unit of cm : XXXX or XXX.X Unit of m : XXXX or XXX.
6.4 RS232C Set up Pic. 19 RS232C set up dialogue box Select contents below from combo box. Correspondence port Baud rate Delimiter COM1, COM2, COM3, COM4 300, 600, 1200, 2400, 4800, 9600, 19200 bps CR, CRLF * When you set up correspondence condition, confirm if it corresponds to ANEMOMASTER main body.
6.5 Measurement Parameter Set up Possible to select measurement times or repeat time Pic. 20 Measurement parameter set up dialogue box Set up contents below. Measurement mode Data mode Interval of measurement time Repeat times Fixed to channel mode Possible to select average mode (Average) or Instant mode (Instant) 0.1~6553.5 seconds, possible to set by every 0.
6.6 Time Series Graph 1) Time series graph indication parameter set up Select only times When you click, dialogue box to select probe to display will appear Pic. 21 Time series graph indication parameter set up dialogue box Set up vertical and horizontal line of time series graph, and select probe to display.
3) Time series graph indication window Statistics data Line cursor Data Pic. 23 Time series graph indication window Items indicated Turn page scroll bar on vertical line Pic.
6.7 Data Table Display 1) Set up data table indication parameter Check items to display Pic. 24 Data table indication parameter set up dialogue box 2) Data table indication window Scroll bar to change sampling time Sampling data of 261’st time is displayed Pic.
6.8 Data Display Windows in Plural Graph 1 Graph 2 Table Pic. 26 Data display windows in plural You can display graphs and tables in plural on screen by adjusting each display size of time series graph and data table.
6.9 Print Out This program is possible to print out time series data graph and data table. Orders of print out: a. Click and active window of time series graph (or data table ) you want to print out. b. Select “Print out” item from “File” menu (or click print out icon of tool bar).
6.10 User Back up Function 1) Version information Pic. 27 Version information dialogue box 2) Tool hint Tool hint Pic. 28 Tool hint When you put mouse pointer on control, tool hint will appear. 3) File information Possible for user to input Pic.
7. Message Dialogue box 7.1 Message Dialogue box “Message dialogue box will be displayed to confirm or indicate error message while the program is run. This program has two kinds of “Message” dialogue boxes as below. 1) “Caution” message dialogue box Title Message Command button Pic. 30 “Caution message” dialogue box 2) “Question” dialogue box Pic.
7.2 Message List “Message” dialogue box consists from “Title” , “Message” and “Command button” as shown in Pic. 30. Following is message list appears while this program is run. 1) “Caution” message list Name of Message dialogue Input Value is not correct. confirmation [###] module is missing. (### : Name of module) Setting confirmation RS232C Error Message Title Check input value Input module type Settings of measurement Set measurement interval is 0.1~6553.5 sec.
2) Question message list Name Message Title Input Value is not correct confirmation Input again? Confirm to Stop data take in? stop measuring Input check Confirm to Change parameter? change parameter Multi-channel ANEMOMASTER soft ware Confirm save file Multi-channel ANEMOMASTER soft ware to Parameter is changed. Save it? There is data in memory.
8. Data Link to Calculation Table Soft This program create data file which can be taken in to calculation table soft at the same time with data saving of Measured data. Data file which can be taken in to calculation table soft File Parameter file Present data file Statistics data file Revised result data file *File name : ###_P.TXT *System : Text system *Contents : System parameter, RS232C parameter, measurement parameter. *File name : ###_R.
② Select [ Text file ] from [ Kinds of files ]. Select [Text file] from [Kinds of files ] Select items according to contents on screen such as delimited of text file.
Select “ General” from data format Preview data format Click finish ④ Text data will taken into work sheet.