READy MTU 8. Choose the menu item Install MTU for AMI. Installation & operation guide Installation Install meter for AMI Install MTU for AMI Remove meter Check readability Network tool 9. Select the meter on which you want to install READy MTU. You can search by serial number or address.
Installation & operation guide READy MTU 11. Set up the encoded output parameters. If a configuration exists, it is shown in the drop-down menu. If no configuration exists, create one and press Next. The latest used configuration will always be chosen by default. Install MTU for AMI 77102199 757623514521 –– Set up encoded output Configuration file Badger 32f Resolution .001 Unit of measurement US Gallon Set up 12. A. Ensure that the Reading is correct before proceeding.
READy MTU 13. Choose the menu item Set up for AMI. Installation & operation guide Install MTU for AMI 77102199 757623514521 –– Done setting up encoded output 77102199 Encoded reading ID 58147.09 US Gallon Reading Back Set up for AMI Done 14. Choose the correct configuration for your AMI network. Press Next. Install MTU for AMI 77102199 757623514521 –– Set up for AMI AMI configuration file 01-51-501 AMI frequency package Springfield East Next 15. Review the configuration.
Installation & operation guide 16. The AMI configuration has been completed, check the readability of the MTU by the AMI network before leaving the installation. READy MTU Install MTU for AMI –– Done configuring for AMI 01-51-501 AMI configuration file AMI frequency package Springfield East Uplink frequency 458875000 Hz Downlink frequency 458875000 Hz Back Check readability Done 17. If the readability is successful, the configuration is complete.
READy MTU Installation & operation guide 9 Operation 9.1 Normal operation After configuration, READy MTU starts forwarding data to READy Collector and READy Manager. The transmission interval is determined by your READy Manager license: • Hourly readings sent every 3 hours • Daily readings sent daily Hourly data is collected and logged via the 3-wire encoded input at the top of the hour and stored for transmission every 3 hours.
Installation & operation guide READy MTU 9.2.2 Reading error Meaning: Data cannot be collected on the encoded communication interface. Possible reasons: • The encoded output cable may be malfunctioning or broken • READy MTU has been disconnected from the meter without enabling transport mode MTU behavior: READy MTU will forward a reading error. The alarm/info code will disappear when a successful reading is obtained again.
READy MTU Installation & operation guide 9.3.3.4 Device scenario B: Meter ID is tracked/CIS imported in READy Manager Meter exchange: • Perform a meter exchange in READy App • Perform an MTU installation in READy App Register exchange: If one of the following steps are not taken, the consumption graphs in READy Manager will fail: • Track meter serial number in CIS instead • Change register in CIS manually • Swap both meter and register 9.3.3.
Installation & operation guide 4. Swipe left and go to the menu item Update devices. 5. Choose the menu item Configure MTU. READy MTU READy Installation Read log Update devices Exchange Update devices Configuration orders Set meter values Change reading setup Firmware update Turn on meter signal Configure MTU 6. Pair with READy Converter. 24 Kamstrup A/S • 55122662_C1_US_06.
READy MTU 7. Select the MTU you want to update. You can search by serial number. Installation & operation guide Install MTU for AMI Select MTU Enter search text 102254 757623514521 757623514525 757623514478 1 2 3 q w e r 4 5 6 7 8 9 t y u i o p 0 a s d f g h j k l z x c v b n m , ?123 8. The configuration shown is the current configuration of the MTU. You can rename the configuration by tapping the three dots next to the Configuration file combo box. .
Installation & operation guide READy MTU 9.6 Decommissioning Ensure that READy MTU is in transport mode when transported by air freight or during decommissioning. Remember to enable transport mode when exchanging or decommissioning READy MTU. If this is not done, the MTU will keep sending alarms with Reading error to the previously connected meter in READy Manager. 1. Sync READy Manager and READy App before proceeding to step 2. 2. Turn on READy Converter. READy Open READy App. 8 3.
READy MTU Installation & operation guide 4. Pair with READy Converter. 5. Choose the menu item Remove device Installation Install meter for AMI Install MTU for AMI Remove device Check readability Network tool 6. Select the device you wish to decommission/deactivate. You can search by serial number or address.
Installation & operation guide 7. Confirm that you want to remove/ decommission the device. READy MTU Remove device 77102199 757623514521 –– Confirm before removing The radio signal will be turned off when you proceed. Back Accept and remove 8. The radio has been deactivated and the device removed from the installation point.
READy MTU Installation & operation guide 11 Disposal Ensure proper disposal of the product. Kamstrup A/S holds an environmental certification according to ISO 14001 and as part of our environmental policy, we use materials that can be disposed of in an environmentally sustainable manner to the greatest extent possible. Please ensure correct disposal of all parts of the device. The enclosure must be disassembled to dispose of the batteries, electronics, and enclosure correctly. 11.
Installation & operation guide READy MTU 12 Ordering details 12.1 Type number Type number is static at the moment. There might be changes in the future. US AMI MTU types are described in below table: READyMTU 6696 Input 3-wire encoded input 22 Communication AMI, dual-band, capable, (2-way) 01 Power supply D-cell D No choice 00 Meter type MTU 8 Country code North America/Canada, FCC approved/ISED approved 20 12.
READy MTU Installation & operation guide 12.3 Other MTU ordering data Resolution/Multiplier ID Blank (configurable with READy APP/READy Manager) 1 .001 2 .01 3 .1 4 1 5 10 6 100 7 1000 8 10,000 9 Unit of measure Blank (configurable with READy APP/READy Manager) 1 Gallon US (USgal) 2 Imperial gallon (IMPgal) 3 Liter 4 Cubic feet 5 Cubic meters 6 Timing parameters Automatic (default) AMI frequency Customer specific 12.
Installation & operation guide Kamstrup Water Metering, LLC 245 Hembree Park Drive, Ste. 110 Roswell, GA 30076, USA T: +1 (404) 835-6716 info-us@kamstrup.com kamstrup.
