ASSEMBLY INSTRUCTION 12'x 10'Steel DOUBLE ROOF GAZEBO Website:www.mondawe.com Customer Service:service@mondawe.
Important Safety Instructions Warning! To reduce the risk of serious injury, read the following safety instructions before assembling and using the gazebo. Please check with your local governing authority/local municipal codes regarding installation of structures before assembly. Caution! Proper placement of your gazebo is essential. Do not place the product underneath electrical lines. Keep children away during assembly. This product contains small parts which can be swallowed by children.
• • • Do not hang heavy weights on the roof frame. Do not climb onto the roof of the gazebo. Falling off the gazebo can result in serious injury. Retain the original packaging to store the gazebo. IMPORTANT: •Please read and understand this manual before any assembly. Before beginning assembly of product, make sure all parts are present. Compare parts with packaging contents list. •If any part is missing, or if you have any questions, contact the service Centre at 888-328-5111.
Connect Stake Plate(L) to bottom of Post(A) by using Bolt (X1) 1-Attach Long Side Beam (B/B1) and Short Side Beam (C/C1) to Post (A), fix by using Bolt (X). 2-Attach Top of Left/Right Slant Support (F/F1) to Assembled beam (B/B1/C/C1) and attached the bottom of Left/Right Slant Support (F/F1) to Post(A), fasten by using Bolt (X4).
Attach assembled Long Side Left Beam (B) & assembled Long Side Right Beam (B1) to Beam Connector(P), fix by using Bolt (X1).
1-Attach Corner Sleeve (J1) to assembled Beam(B/B1/C/C1), fasten by using Bolt (X4). 2-Attach Rib Supports (J2) to middle of assembled Beam(B/B1 /C/ C1), fasten by using Bolt (X4). 1-Slide 5 Hooks(Q) into long sides beams(B/B1). 2-Slide 4 Hooks(Q) into short sides beams(C/C1). 3-Attach part M6 to inside beams(B/B1/C/C1)fix by using Bolt(X4) Note: There are two tracks.
attach the top of long roof ribs (E) to the Roof Top Brace(K1)fix by using Bolt (X1)
attach the tail of long roof ribs (E) to 4 Posts(A) top Corner fix by using Bolt (X1) 1-attach the top of 4 short roof ribs(D) to Roof Top Brace(K1) fix by using Bolt (X1)2attach the tail of 4 short roof ribs(D) to the middle of 4 crossbeams（B and B1、C and C1) fix by using Bolt (X1)
1-first attach the 2 long roof supports(H) to connectors(M3), and 2 short roof supports (I) to connectors(M3) ，fix by using Bolt (X1） 2-attach assembled long roof supports(H) and short roof supports（I） to connectors（M4），fix by using Bolt (X1)，);then install assembled long roof supports(H) and assembled short roof supports (I) to the 4 short roof ribs(D) fix by using bolt(X6) attach the clips(R1) and clips(R）as shown in the diagram
1-Install the Roof Plates （N5、N6、Y6、Y5) on the Long Sides of the Gazebo.
1-Install the Roof Plates （N1、N2、N3、N4、Y1、Y2、Y3、 Y4) on the Long Sides of the Gazebo. fix by using bolt（X6、X5、X3、X2） Please note that when installing the screws (X5 and X2) again, you need to put on M5 1-Install the Roof Plates （O1、O2、O3、O4、V1、V2、 V3、V4) on the short Sides of the Gazebo.
1-first fix M2 with X1 to 4 roof Corner ,but do not screw too tight,then install the fix beams(G1、G2 、G3、G4)，finally tighten the (X1) 2-fix M1 with X1 to the Middle of long fix beams(G1、G2 、G3、G4）
Tighten the screw (X7 and X1) halfwy，then install the fix beams (G7 and G8) and baffle (Z2、Z3、Z4）from left to right as shown ，finally tighten the (X7 and X1)
install the mosquito netting as shown in the diagram
