Installation Sheet

ManualsBrandsKaba Ilco ManualsHardwareSimplex 5000 Mechanical Pushbutton Combination Exit Trim with Entry Key Override

1110

I-8 Remove the interchangeable/removable core.

Then remove the tailpiece (e).

Note: You may want to use needle nose pliers for

some tailpieces.

I-9 Insert the lever release tool (d) into the small hole

(f) under lever as shown. Gently push lever catch up

until it clicks. Remove tool, then remove outside lever (b).

J. INSTALLING SIMPLEX 5000 EXIT TRIM:

Note: Prior to mounting the lock, ensure the handing is set correctly

as the tailpiece may have shifted during handling (see section F)

J-1 Guide the unit assembly so the tailpiece (a) engages the vertical slot in

the hub of the exit device. The key override may be utilized to test the

operation to make sure that the tailpiece is engaged with the exit device

hub before fastening assembly to the door.

J-2 Then insert the three mounting

bushings (d) into the holes on the

inside of the door, and thread the

mounting screws (e) in to the sex

bolts and tighten securely.

Note: Do not close the door until testing the

operation of the lock and exit device as

described in step K below.

K. TESTING THE OPERATION OF

THE LOCK

K-1 Depress the push pad of the exit device and hold. Ensure that the latch is

fully retracted. Release the push pad; the latch should return to the fully

extended position.

K-2 Enter the factory set combination: Depress buttons 2 and 4 at the same

time (& release), then press button 3 (& release), then depress the

“ENTER” button and release. You should feel a slight click as each button

is depressed.

K-3 Rotate the outside lever downward and hold. Ensure that the latch is

retracted sufficiently to clear the strike. Release the outside lever; the

latch should be fully extended.

K-4 Press the “ENTER” button only, and release, then rotate the outside lever.

The latch should not retract.

Note: For all interchangeable/removable cores

except ASSA/Medeco/Yale, proceed to section I-3.

For ASSA/Medeco/Yale cores, skip to section I-5.

I-3 Insert the supplied tailpiece (e) vertically into the

outside lever (b) as shown. Make certain that you rotate

the tailpiece so that it will align with the interchangeable

core. For screw cap type cores (Schlage) (g), the tailpiece

must be assembled to the core first (vertical position).

Insert the interchangeable core into the outside lever.

Note: To remove the outside lever from the

outside unit assembly, follow the steps below.

I-4 Remove the interchangeable core (g).

Then remove the tailpiece (e).

Note: You may want to use needle nose pliers

for some tailpieces.

Insert the release tool (d) into the small hole (f) under lever as shown. Gently

push lever catch up until it clicks. Remove tool, then remove outside lever (b).

I-5 For ASSA/Medeco/Yale interchangeable/removable cores, the tailpiece

must be prepped for the desired length before installation.

When using a Yale

core on a cylindrical

latch application, measure the door

thickness of the intended application.

I-6 Notice the score marks on the flat portion

of the ASSA/Medeco/Yale tailpiece. Using

the diagram to the right, locate the score

mark on your tailpiece that matches your

core prep for the intended application,

and break the tailpiece off accordingly.

Using two pairs of pliers, break the tailpiece to

the desired length of the intended application by

holding one pair of pliers on the good side of

the score mark and a second pair on the other

side of the score mark. Slowly move the 2nd

pair of pliers up and down until the unneeded

portion of the tailpiece breaks free.

I-7 Insert the ASSA/Medeco/Yale tailpiece (e) vertically

into the outside lever as shown. Make certain that

you rotate the tailpiece slightly so that it will align

with the interchangeable/removable core. Insert the

interchangeable/removable core into the outside lever.

Note: To remove the outside lever from the outside unit

assembly, follow steps below.

vertical

ertical

YALE 6 & 7 PIN,

CYLINDRICAL – THIN DOOR

⁄8" (35 mm) to 1

⁄2" (38 mm))

(DO NOT SHORTEN TAILPIECE -

For 1

⁄8" (41 mm) to 2

⁄4" (57 mm))

ASSA/MEDECO 5, 6 & 7 PIN,

CYLINDRICAL – DO NOT

SHORTEN TAILPIECE

ASSA & MEDECO 6 PIN,

EXIT & MORTISE

MEDECO 5 PIN,

EXIT & MORTISE

YALE 6 & 7 PIN,

EXIT & MORTISE

vertical