® Simplex 5010 Exit Trim Installation Instructions Kaba Access Control 2941 Indiana Avenue Winston-Salem, NC 27105 USA Tel: (800) 849-8324 (336) 725-1331 Fax: (800) 346-9640 (336) 725-3269 www.kabaaccess.
TABLE OF CONTENTS Simplex 5000 Assembly Drawing (Simplex 5000 Exit Trim) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 A. Door Preparation – Exit Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 B. Door Preparation – Simplex 5000 Exit Trim . . . . . . . . . . . . . . . . . . . . . .
OPERATIONAL NOTE: The Simplex 5000 Exit Trim lock is in most ways identical to the Simplex 5000 Cylindrical lock with the exception of the operation of the lever and the key override system. When the handing is properly set, rotating the lever upwards will not actuate the latch. The key override system differs in that rotating the key does not actuate the latch as on cylindrical drive models.
B-1 E. ASSEMBLE OUTSIDE UNIT TO UNIVERSAL MOUNTING PLATE: a b For New Installations (Existing Installations proceed to section B-2): Place paper template (supplied) onto the inside of the door and align with the Centerlines. Mark d the location of the Simplex 5000 Exit Trim lock mountc ing holes. Drill the three 3⁄8" holes through the door, e then use a hole saw to cut the 2 1⁄8" bore through the door at the intersection of the Vertical and Horizontal Centerlines.
H-1 Make certain the lever catch is up as shown (c). Position the lever sleeve (f) tab correctly with the respective notch on the lever. The lock comes shipped with the lever sleeve already installed in the lock housing. When installing lever, ensure it is oriented to engage the lever sleeve to accommodate desired lock handing as shown. G-2 Determine the proper tailpiece (d) from the chart below for your KIL cylinder. You must use a factory shortened Kaba tailpiece.
Kaba Access Control warrants this product to be free from defects in material and workmanship under normal use and service for a period of three (3) years. Kaba Access Control will repair or replace, at our discretion, 5000 Series Locks found by Kaba Access Control analysis to be defective during this period. Our only liability, whether in tort or in contract, under this warranty is to repair or replace products that are returned to Kaba Access Control within the three (3) year warranty period.
Name Position Company Address City State Phone Email Lock Model Number Date of Purchase Name of Dealer Purchased From ZIP (Postal Code) Country Thank you for purchasing our product. In order to protect your investment and to enable us to better serve you in the future, please fill out this registration card and return it to Kaba Access Control, or register online at www.kabaaccess.com.
a Note: For all interchangeable/removable cores except ASSA/Medeco/Yale, proceed to section I-3. For ASSA/Medeco/Yale cores, skip to section I-5. g vertical I-3 I-8 e g Note: You may want to use needle nose pliers for some tailpieces. b Insert the supplied tailpiece (e) vertically into the outside lever (b) as shown. Make certain that you rotate the tailpiece so that it will align with the interchangeable core.
K-5 Insert one of the supplied keys into the outside lever. Rotate key counter clockwise till it stops (approximately 90 degrees), while holding the key in this position with one hand, use the other hand to rotate the lever downwards till it stops and hold (once the lever has rotated a few degrees the key may be released). Ensure that the latch has retracted sufficiently to clear the strike. Release the lever once more and ensure that the latch is fully extended. L.
M-4 Resetting and Recovery of Current Code To reset the code gears (a), each one of the 5 “L” shaped legs (b) of the unlocking slide (c) must engage snugly with the corresponding code gear pocket (d) next to it. Note: If you depress the wrong key stem by mistake, rotate the reset cam back toward you, (toward the key stems and release). This resets the code gears and you must repeat the above procedure.
N. TROUBLE SHOOTING SYMPTOM POSSIBLE CAUSE SYMPTOM REMEDY 1. The outside lever always retracts the latch after depressing and releasing the “ENTER” button only (without combination). Lock is in “ZERO” combination. Follow the procedure for Changing Combinations (Section M) except omit steps 1 and 2 (do not enter the existing combination). 2. The outside lever will not go completely inside the outside unit assembly. Lever catch is misaligned.
Notes 18 Notes 19
