User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
(1) Operational use conditions
Module has professional users use condition limitations, Host product
manufacturer please ensure giving such warning like “Product is limited to
professional users use” in your product’s instruction.
(2) Antenna used
Antenna
Type
Max. Antenna
Gain
PCB 0dBi
(3) Labelling Instruction for Host Product Integrator
Please notice that if the FCC and IC identification number is not visible when the
module is installed inside another device, then the outside of the device into which
the module is installed must also display a label referring to the enclosed module.
For FCC, this exterior label should follow “Contains FCC ID: 2A769-PN7150”. In
accordance with FCC KDB guidance 784748 Labeling Guidelines. For IC, this
exterior label can use wording “Contains IC: 28842-PN7150”.
§ 15.19 and RSS-Gen Labelling requirements shall be complied on end user device.
Labelling rules for special device, please refer to §2.925, § 15.19 (a)(5) and relevant
KDB publications. For E-label, please refer to §2.935.
(4) Installation Notice to Host Product Manufacturer
The OEM integrator is responsible for ensuring that the end-user has no manual
instruction to remove or install module.
The module is limited to installation in mobile application, a separate approval is
required for all other operating configurations, including portable configurations
with respect to §2.1093 and difference antenna configurations.
(5) Antenna Change Notice to Host manufacturer
If you desire to increase antenna gain and either change antenna type or use same
antenna type certified, a Class II permissive change application is required to be
filed by us, or you (host manufacturer) can take responsibility through the change
in FCC ID and IC ID (new application) procedure followed by a Class II permissive
change application.
(6) FCC other Parts, Part 15B Compliance Requirements for Host product
manufacturer
This modular transmitter is only FCC authorized for the specific rule parts listed on
our grant, host product manufacturer is responsible for compliance to any other
FCC rules that apply to the host not covered by the modular transmitter grant of
certification.
Host manufacturer in any case shall ensure host product which is installed and