User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
99 of 127
P
ayload Field(s)
L
ength
V
alue/Description
R
esult_Parameter_2 1 Octet Value depending on the measurement performed :
see →Table 101
R
esult_Parameter_3 1 Octet Value depending on the measurement performed :
see →Table 101
R
esult_Parameter_4 1 Octet
Value depending on the measurement performed :
see →Table 101
Table 100. Parameters provided in TEST_ANTENNA_RSP as a result of the measurement performed
Meas.
ID
Measurement
D
escription
Param.
nbr
P
arameter name
L
ength
D
escription
0x01
TxLDO current
measurement
1 TxLDO output value 1 Octet Raw value (RawVal) of TxLDO measurement (0x00-
0x7F)
2 Measured range 1 Octet
0x
00 50-100 mA
Absolute value = 0.4 x RawVal + 50 [mA]
0x01 20-70 mA
Absolute value = 0.4 x RawVal + 20 [mA]
3 RFU 1 Octet
4 RF
U 1 Octet
0x
02
AGC value
reading
1 AGC Value LSB 1 Octet
2 AG
C Value MSB 1 Octet
3 RFU 1 Octet
4 RF
U 1 Octet
0x
04
AGC value
reading with
fixed NFCLD
level
1 AGC Value LSB 1 Octet
2 AG
C Value MSB 1 Octet
3 RF
U 1 Octet
4 RFU 1 Octet
4 AG
C Value MSB 1 Octet
0x
20
Switch RF Field
On/Off
1 RFU 1 Octet
2 RFU 1 Octet
3 RF
U 1 Octet
4 RF
U 1 Octet
!
R
FU Bytes in TEST_ANTENNA_RSP can have any value from 0x00 to 0xFF.
11.4 TEST_GET_REGISTER_CMD/RSP
T
his command is used to retrieve the current Value of the AGC_VALUE_REGISTER.