User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
11 of 127
2.
1.3 Transport Mappings
T
ransport Mappings define how the NCI messaging is mapped to an underlying NCI
Transport, which is a physical connection (and optional associated protocol) between the
DH and the NFCC. Each Transport Mapping is associated with a specific NCI Transport
(see [NCI] for definition).
2
.2 NCI Concepts
This chapter outlines the basic concepts used in
[N
CI]
.
NFC Forum Device
NCI
NFCC
DH
NFCEE
Remote NFC
Endpoint
NFCEE Protocol
RF Protocol
RF Interface
Control Messages
Data Messages
Control Messages
NFCEE Interface
Data Messages
Control Messages
F
ig 8. NCI concepts
2.
2.1 Control Messages
A
DH uses NCI Control Messages to control and configure an NFCC. Control Messages
consist of Commands, Responses and Notifications. Commands are only allowed to be
sent in the direction from DH to NFCC, Responses and Notifications are only allowed in
the other direction. Control Messages are transmitted in NCI Control Packets, NCI
supports segmentation of Control Messages into multiple Packets.
The NCI Core defines a basic set of Control Messages, e.g. for setting and retrieving of
NFCC configuration parameters. NCI Modules can define additional Control Messages.