User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
96 of 127
1
1. Test Mode
11.1 Test Session
T
he PN7150 has the ability to generate a continuous PRBS pattern on the RF interface.
Whatever the test command used by the DH, it is necessary to implement a "test session",
which isolates the test mode from a regular "NCI session" of PN7150. This test session is
defined thanks to the following sequence:
• Reset/Initialize the PN7150 using CORE_RESET_CMD/CORE_INIT_CMD
• Launch selected test function
• Get the response transporting executed test status
• Reset/ Initialize the PN7150 using CORE_RESET_CMD/CORE_INIT_CMD (except
for TEST_PRBS_CMD, which requires a HW reset first to stop the pattern generation
on RF).
11.2 TEST_PRBS_CMD/RSP
T
his command is used to start PRBS infinite stream generation:
T
able 91. TEST_PRBS_CMD
G
ID
O
ID
Numbers of
p
arameter(s)
D
escription
1111b 0x
30 6 Command to start PRBS generation
Table 92. TEST_PRBS_CMD parameters
Payload Field(s) Length Value/Description
PR
BS Mode 1 Octet
0x
00 Firmware PRBS
0x
01 Hardware PRBS
PRBS type 1 Octet
0x
00 PRBS9
0x
01 PRBS15
T
echnology to stream 1 Octet
0x
00 Type A
0x01 Type B
0x
02 Type F
Bi
trate 1 Octet
0x00 106 kbps (Type A,B)
0x01 212 kbps (Type A,B& F)
0x
02 424 kbps (Type A,B & F)
0x
03 848 kbps (Type A,B)
PRBS series length 2 Octets A value between 0x0001 – 0x01FF