User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
93 of 127
10.
2.2 Listen Mode
T
able 85. Listen Mode Configuration
Na
me & Rights
D
escription
Ex
t. Tag
L
en.
D
efault
Value
T
O_RF_OFF_CFG
RW in E²PROM
Specifies the time out (in ms) applied by PN7150 before it
restarts a Polling sequence, after it has detected a Field OFF
in Listen Mode
0xA0 0x80 2 0x012C
(300 ms)
L
ISTEN_PROFILE_SEL_
CFG
RW in E²PROM
Discovery profile selection in Listen Mode, as follows:
0x00 NFC FORUM profile
0x
01 EMVCo
0x
02- 0xFF RFU
0
xA0 0x81 1 0x01
L
ISTEN_ISODEP_FSCI_
CFG
RW in E²PROM
Parameter to define the FSC parameter (RF Frame Size for
the PICC), as defined in [14443-4]:
0x00 FSC = 16
0x01 FSC = 24
0x
02 FSC = 32
0x
03 FSC = 40
0x
04 FSC = 48
0x05 FSC = 64
0x
06 FSC = 96
0x
07 FSC = 128
0x08 FSC = 256
0x
09- 0xFF RFU
0
xA0 0x83 1 0x08
10.3 [PN7150-NCI] extension: Contactless Interface configurations
P
N7150 offers multiple configuration options for the Contactless Interface, to allow an
optimum match between the antenna characteristics and the transmitter and receiver in
PN7150. A generic TLV mechanism has been defined to write the Contactless Interface
settings. It relies on the [NCI] CORE_SET_CONFIG_CMD and is described hereafter:
T
able 86. Mechanism to configure the RF transitions:
Na
me & Rights
D
escription
Ex
t. Tag
L
en.
Default
Va
lue
RF_TRANSITION_CFG
RW in E²PROM
Parameter to configure one RF transition.
•
O
ne transition will be coded as:
T
ransition ID
(TID)
CLIF register offset
(RO)
Register Value
(RV)
1 Byte 1 Byte
1 Byte
2 Bytes
4
Bytes
0xA0 0D 3, 4 or 6 N/A