User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
92 of 127
Na
me & Rights
D
escription
Ex
t. Tag
L
en.
D
efault
Value
I
n both cases, the RF_INTF_ACTIVATED_NTF will NOT
embed the RID response from the T1T, as defined in [NCI].
F
ELICA_TSN_CFG
RW in E²PROM
TSN value transported by the PN7150 in the SENSF_REQ
command: the DH defines the number of time slots for
collision resolution.
!! This value has to be set to 0x03 for NFC FORUM
compliance (DTA/Digital protocol tests) !!
0x
A0
0x
5F
1 0x
00
TechDet_AFTER_LPCD_
CFG
RW in E²PROM
Parameter used to configure the RF Discovery taking place
right after the Low Power Card Detector has triggered a
detection:
Bit Mask Description
b7 b6 b5 b4 b3 b2 b1 b0
X X X X X TechDet_PERIOD
In steps of 10ms
X X X T
echDet_NBR_RETRIES
S
ee →9.4.2 for more details on the use of this parameter.
0x
A0
0x61
1 0x00
1
W
O (Write Only) parameters can only be written, using CORE_SET_CONFIG_CMD.
PN7150 will always return CORE_GET_CONFIG_RSP(STATUS_INVALID_PARAM) to
any attempt to read the value of the WO parameter.