User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
91 of 127
Na
me & Rights
D
escription
Ex
t. Tag
L
en.
D
efault
Value
M
FC_KEY-3_CFG
WO
1
in E²PR
OM
Key 3, used in MIFARE Classic Authentication command. 0xA0 0x50
6 0xFFFF
FFFF
FFFF
M
FC_KEY-4_CFG
WO
1
in E²PR
OM
Key 4, used in MIFARE Classic Authentication command. 0xA0 0x51
6 0xFFFF
FFFF
FFFF
M
FC_KEY-5_CFG
WO
1
in E²PROM
Key 5, used in MIFARE Classic Authentication command.
0xA0 0x52
6
0xFFFF
FFFF
FFFF
M
FC_KEY-6_CFG
WO
1
in E²PR
OM
Key 6, used in MIFARE Classic Authentication command. 0xA0 0x53
6 0xFFFF
FFFF
FFFF
M
FC_KEY-7_CFG
WO
1
in E²PROM
Key 7, used in MIFARE Classic Authentication command.
0xA0 0x54
6
0xFFFF
FFFF
FFFF
M
FC_KEY-8_CFG
WO
1
in E²PR
OM
Key 8, used in MIFARE Classic Authentication command. 0xA0 0x55
6 0xFFFF
FFFF
FFFF
MFC_KEY-9_CFG
WO
1
in E²PROM
Key 9, used in MIFARE Classic Authentication command. 0xA0 0x56
6 0xFFFF
FFFF
FFFF
M
FC_KEY-10_CFG
WO
1
in E²PR
OM
Key 10, used in MIFARE Classic Authentication command.
0xA0 0x57
6
0xFFFF
FFFF
FFFF
MFC_KEY-11_CFG
WO
1
in E²PROM
Key 11, used in MIFARE Classic Authentication command. 0xA0 0x58
6 0xFFFF
FFFF
FFFF
M
FC_KEY-12_CFG
WO
1
in E²PR
OM
Key 12, used in MIFARE Classic Authentication command.
0xA0 0x59
6
0xFFFF
FFFF
FFFF
MFC_KEY-13_CFG
WO
1
in E²PROM
Key 13, used in MIFARE Classic Authentication command. 0xA0 0x5A
6 0xFFFF
FFFF
FFFF
M
FC_KEY-14_CFG
WO
1
in E²PR
OM
Key 14, used in MIFARE Classic Authentication command. 0xA0 0x5B
6 0xFFFF
FFFF
FFFF
MFC_KEY-15_CFG
WO
1
in E²PROM
Key 15, used in MIFARE Classic Authentication command.
0x
A0
0x5C
6 0xFFFF
FFFF
FFFF
F
SDI_CFG
RW in E²PROM
Frame Size value for the PN7150 to display in RATS or
ATTRIB.
0x
A0
0x
5D
1 0x
08
J
EWEL_RID_CFG
RW in E²PROM
Parameter used to configure if the RID is sent on RF to the
T1T by PN7150 during the RF activation or not:
0x01 => The RID is sent on RF to the T1T
0x00 => The RID is NOT sent on RF to the T1T
0x
A0
0x
5E
1 0x
00