User's Manual

U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
90 of 127
Na
me & Rights
D
escription
Ex
t. Tag
L
en.
D
efault
Value
T
AG_DETECTOR_
FALLBACK_CNT_CFG
RW in E²PROM
Parameter used to configure the "Hybrid" mode ton insert a
regular Polling cycle every N pulses generated by the LPCD:
0x00 Hybrid mode disabled: LPCD only, no
regular Polling cycle unless an "object" is
detected by the LPCD.
0x
02- 0xFF
Hybrid mode enabled, inserting a regular
Polling cycle every 'N' pulses of LPDC.
'N' is coded by the value assigned to
TAG_DETECTOR_FALLBACK_CNT_CFG
in decimal.
0
xA0 0x43 1 0x50
P
OLL_PROFILE_SEL_
CFG
RW in E²PROM
Discovery profile selection in Poll Mode as follows:
0x00 NFC FORUM profile
All static configurations (Bail-out) will be
set to the [NCI] default value (disabled).
0x01 EMVCo profile
0x
02- 0xFF RFU
0
xA0 0x44 1 0x00
GT_NFC-AA_CFG
RW in E²PROM
Guard time (in steps of 0.59µs) used between the start of
unmodulated RF field & 1
st
c
ommand for Poll NFC-A Active
(min=’0001’, max=’FFFF’)
0xA0 0x46 2 0x21C4
(5.1ms)
G
T_NFC-AP_CFG
RW in E²PROM
Guard time (in steps of 0.59µs) used between the start of
unmodulated RF field & 1
st
c
ommand for Poll NFC-A Passive
(min=’0001’, max=’FFFF’)
0xA0 0x47 2 0x2219
(5.15ms)
G
T_NFC-B_CFG
RW in E²PROM
Guard time (in steps of 0.59µs) used between the start of
unmodulated RF field & 1
st
command for Poll NFC-B Passive
(min=’0001’, max=’FFFF’)
0xA0 0x48
2
0x2219
(5.15ms)
G
T_NFC-F_CFG
RW in E²PROM
Guard time (in steps of 0.59µs) used between the start of
unmodulated RF field & 1
st
c
ommand for Poll NFC-F Passive
(min=’0001’, max=’FFFF’)
No
te: If previous phase on polling loop is a FeliCa Poll that fail
on T
imeout, you will see an additional 5 ms delay due to the
FeliCa timeout itself
0
xA0 0x49 2 0x878D
(20.47ms
)
GT_15693_CFG
RW in E²PROM
Guard time (in ms) used between the start of unmodulated RF
field & 1
st
c
ommand for Poll 15693 Passive (min=’0001’,
max=’FFFF’)
0xA0 0x4A
2
0x07B8
(1.17ms)
PF
_SYS_CODE_CFG
RW in E²PROM
Discovery configuration parameters for Poll F: system code
0x
A0
0x
4C 2 0xFFFF
MFC_KEY-0_CFG
WO
1
in E²PR
OM
Key 0, used in MIFARE Classic Authentication command.
0x
A0
0x
4D
6
0xA0A1
A2A3
A4A5
M
FC_KEY-1_CFG
WO
1
in E²PR
OM
Key 1, used in MIFARE Classic Authentication command. 0xA0 0x4E 6 0xD3F7
D3F7
D3F7
MFC_KEY-2_CFG
WO
1
in E²PR
OM
Key 2, used in MIFARE Classic Authentication command.
0xA0 0x4F
6
0xFFFF
FFFF
FFFF