User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
89 of 127
T
able 83. DYN_LMA_SETTINGS_CFG Description
B
ytes
D
escription
L
en.
D
efault
Va
lue
0 … 1 RFU 2 N/A
2 bLutSize: Size of LUT, DO NOT MODIFY this parameter 1 0x10
3
bN
bLutEntries: Number of entries in DynLma look up table
. bits 0:3 = Number of Entries for Type A/B (0 means LMA disabled for this Type)
. bits 4:7 = Number of Entries for Type F (0 means LMA disabled for this Type)
The number of entries for Type A/B + Type F shall not exceed the Total number of Entries.
The Entries for TypeF follow the ones for Type A/B. This means if number of entries for
Type A/B is 8 Entry 8 is the first for TypeF
1 0x00
4
dw
LutEntry0:
bits 20:18 = TXLDO output voltage: PMU_TXLDO_CONTROL_REG/TXLDO_SELECT
bits 17:16 = CLIF_ANA_TX_AMPLITUDE_REG / TX_CW_AMPLITUDE_ALM_CM
bit 15 = CLIF_TX_CONTROL_REG / TX_ALM_TYPE_SELECT
bits 14:10 = CLIF_ANA_TX_AMPLITUDE_REG / TX_RESIDUAL_CARRIER
bits 09:00 = AGC_VALUE
4 0x037C02
...
dwLutEntry…
4 N/A
6
4 ... 67
dwLutEntryF
4 0x000032
10.2 [PN7150-NCI] extension: RF Discovery configuration
10.
2.1 Poll Mode
S
everal configuration parameters are required for the Poll Mode in RF discovery:
T
able 84. Poll Mode configuration
Na
me & Rights
D
escription
Ex
t. Tag
L
en.
D
efault
Value
T
AG_DETECTOR_CFG
RW in E²PROM
Tag detector enabling/disabling as follows:
Bit Mask Description
b7 b6 b5 b4 b3 b2 b1 b0
X
D
etection based on the
AGC
X
A
ctivation of the Trace
mode
0 0 0 0 0 0 RFU
'
1' => Enabled; '0' => Disabled
0xA0 0x40 1 0x00
TAG_DETECTOR_
THRESHOLD_CFG
RW in E²PROM
Sets the detection level.
0xA0 0x41 1 0x04
T
AG_DETECTOR_
PERIOD _CFG
RW in E²PROM
Time in steps of 8us to wait before reading the AGC value.
0xA0 0x42 1 0x0F