User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
65 of 127
7
. Card Emulation Mode
T
he PN7150 supports Card Emulation hosted by the DH based on either technology NFC-
A, NFC-B or NFC-F.
7.1 ISO-DEP card emulation through NFC-A & NFC-B
[
NCI] defines all the mechanisms necessary to implement this feature. Two options are
possible:
1. The DH wants to manage by itself the ISO-DEP protocol; it SHALL
then map the ISO-DEP protocol on the Frame RF Interface.
!
N
ot supported in PN7150
2. T
he DH leaves the ISO-DEP protocol management to the NFCC: it
SHALL then map the ISO-DEP protocol on the ISO-DEP interface.
H
ere are the commands and configuration parameters to prepare the ISO-DEP Card
Emulation for technology NFC-A in the DH through the ISO-DEP RF Interface:
T
able 67. Config. seq. for CE of ISO-DEP/NFC-A
C
ommand
M
ain Parameters
V
alues
RF
_DISCOVER_MAP_CMD
RF Protocol PROTOCOL_ISO-DEP
M
ode Listen
RF Interface ISO-DEP
CO
RE_SET_CONFIG_CMD
LA_BIT_FRAME_SDD
LA
_PLATFORM_CONFIG
LA_SEL_INFO
L
A_NFCID1
L
I_FWI
LA_HIST_BY
LI
_BIT_RATE
RF
_DISCOVER_CMD RF Technology & Mode NFC_A_PASSIVE_LISTEN_MODE
H
ere are the commands and configuration parameters to prepare the ISO-DEP Card
Emulation for technology NFC-B in the DH through the Frame RF Interface:
T
able 68. Config. seq. for CE of ISO-DEP/NFC-B
C
ommand
M
ain Parameters
V
alues
RF
_DISCOVER_MAP_CMD
RF Protocol PROTOCOL_ISO-DEP
M
ode Listen
R
F Interface ISO-DEP
CO
RE_SET_CONFIG_CMD
LB_SENSB_INFO
L
B_NFCID0