User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
60 of 127
D
etailed ISO-DEP RF Interface activation handling in the NFCC:
For NFC-A:
Following the anticollision sequence, if the Remote NFC Endpoint supports ISO-DEP
Protocol, the NFCC sends the RATS Command to the Remote NFC Endpoint. And after
receiving the RATS response, the PN7150 MAY send the PPS command if PI_BIT_RATE
was set by the DH to an allowed value higher than 0x00. It SHALL then send the
RF_INTF_ACTIVATED_NTF to the DH to indicate a Remote NFC Endpoint based on
ISO-DEP has been activated. The RF_INTF_ACTIVATED_NTF will inform the DH on
the actual bit rate used on RF.
For NFC-A the RF_INTF_ACTIVATED_NTF SHALL include the Activation
Parameters defined in Table 74 (see below).
T
able 74: Activation Parameters for NFC-A/ISO-DEP Poll Mode
P
arameter
Le
ngth
D
escription
R
ATS Response Length 1 Octet Length of RATS Response Parameter (n)
R
ATS Response n Octets
All Bytes of the RATS Response as defined in
[DIGITAL] starting from and including Byte 2.
____
__________________ End of Copy from [NCI] __________________________
6.4 [PN7150-NCI] extension: 15693 & I-Code tags
T
he current version of the NCI standard allows the data exchange with a tag ISO15693 by
using the RF Frame interface. No additional interface is needed for this protocol. However,
the data mapping is not yet defined in [NCI], therefore, NXP has defined it for [PN7150-
NCI].
6.
4.1 Access through the Frame RF Interface
T
he Frame RF interface allows full access to all the Tags based on NFC-15693 technology.
Here is a list of such tags from the NXP portfolio:
Table 62. NFC-15693 compliant Tag/Cards accessible over the Frame RF Interface
T
ag/Card
Access through the
F
rame RF Interface
I-C
ode SLI
I-Code SLI-L
I-Code SLI-S
H
ere are the commands and configuration parameters to prepare the Reader/Writer Mode
for NFC-15693 Tags/Cards through the Frame RF Interface: