User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
57 of 127
T
able 51. RF_PRES-CHECK_RSP
G
ID
O
ID
N
umbers of
p
arameter(s)
D
escription
1111b 0x11 1 The NFCC acknowledges the command received from the DH.
Table 52. RF_PRES-CHECK_RSP parameters
Payload Field(s) Length Value/Description
ST
ATUS 1 Octet One of the following Status codes, as defined in [NCI_Table1]
0x00 STATUS_OK
0x
01 STATUS_REJECTED
0x
06 STATUS_SEMANTIC_ERROR
Others Forbidden
T
able 53. RF_PRES-CHECK_NTF
GID OID
N
umbers of
p
arameter(s)
Description
1111b 0x11 1 NFCC indicates if the ISO-DEP Tag/Card is still in the field or not.
Table 54. RF_PRES-CHECK_NTF parameters
Payload Field(s) Length Value/Description
Pre
sence 1 Octet
0x
00 Card no more in the field
0x
01 Card still in the field
0x02-0xFF RFU
6.
3.4 [PN7150-NCI] extension: S-Block Command/Response
I
n some circumstances the DH may want to send specific S-Block to the remote card.
All the rules defined for command/response in [NCI] (section 2.2) apply to the commands
defined here. Here are two additional rules:
The DH SHALL not issue these commands if the ISO-DEP RF Interface is not
activated.
If the DH issues such a command although the ISO-DEP RF Interface is not
activated, the NFCC SHALL send the corresponding response with STATUS set
to STATUS_SEMANTIC_ERROR.
T
able 55. RF_T4T_SBLOCK_PARAM_CMD
G
ID
O
ID
N
umbers of
p
arameter(s)
D
escription
1111b 0x10 1 Command to allow the DH to send S-Block S(PARAMETERS) over RF.