User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers. . All rights reserved.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
46 of 127
6
. Reader/Writer Mode
6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
N
ote: all the Tags/Cards in this category are based on NFC-A technology, but they do not
s
upport the ISO-DEP Protocol.
MI
FARE Plus cards support the ISO-DEP protocol, but only when they are configured in
Security Level3, which is out of scope for this section.
6.
1.1 Access through the [NCI] Frame RF Interface
[
NCI] allows the data exchange with tags T1T, T2T using the Frame RF Interface.
Most of the commands of the MIFARE Classic and MIFARE Plus can also be mapped on
the Frame RF Interface, but NXP decided to use a separate RF interface (TAG-CMD, see
→6.1.2) because some MIFARE Classic commands are split in 2 steps (e.g. Authenticate
command) and have a tight response timeout (about 1ms) which can hardly be monitored
by the DH through the NFCC.
Here is a summary of the Tags/Card based on technology NFC-A which can be accessed
through the Frame RF interface
Table 27. Tag/Cards accessible over the [NCI] Frame RF Interface
Tag/Card Access through the Frame RF Interface
T
1T
T2T
M
IFARE Ultralight, Ultralight C
MIFARE Classic
M
IFARE Plus for Security levels 1 & 2
H
ere are the commands and configuration parameters to prepare the Reader/Writer Mode
for T1T & T2T through the Frame RF Interface:
Table 28. Config. seq. for R/W of T1T or T2T through the Frame RF Intf
Command Main Parameters Values
RF
_DISCOVER_MAP_CMD*
RF Protocol (choose between
the 2 possible protocols)
PROTOCOL_T1T
PROTOCOL_T2T
M
ode Poll
RF Interface Frame RF Interface
CO
RE_SET_CONFIG_CMD PA_BAIL_OUT*
RF
_DISCOVER_CMD RF Technology & Mode NFC_A_PASSIVE_POLL_MODE
* No
te: RF_DISCOVER_MAP_CMD is optional since the mapping to Frame RF Intf. is done by default
*
this parameter is not active in PN7150: it can be read/written, but PN7150 will always
behave with Bail Out in NFC-A, whatever the value written by the DH to that parameter.