User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
42 of 127
O
n this figure,
Green background means mandatory exchange
Blue background means optional exchange, depending on the use case.
Start RF Discovery
Optional: Load the Listen Mode Routing Table
Optional: if default RF parameters need to be modifed
Optional: if Protocol to RF Interface default mapping does not fit
Optional: if system includes some NFCEEs
Reset / Init Sequence (atomic, cannot be split)
DH NFCC
CORE_INIT_CMD
CORE_IN
IT_RSP
CORE_RESET_CMD
(Rese
t Type = Reset Configuration)
RF_DISCOVER_MAP_CMD
RF_DISCOVER_MAP_RSP
CORE_SET_CON
FIG_CMD
CORE_SET_CON
FIG_RSP
RF_SET_LISTEN_MODE_ROUTIN
G_CMD
RF_SET_LISTEN_MODE_ROUTING_RSP
CORE_RESET_RSP
N
FCEE_DISCOVER_CMD
N
FCEE_DISCOVER_RSP
RF_DISCOVER_CMD
RF_N
FCEE_DISCOVERY_REQ_NTF
RF_N
FCEE_DISCOVERY_REQ_NTF
Activate NXP proprietary extensions
N
CI_PROPRIETARY_ACT_CMD
N
FCEE_DISCOVER_NTF
RF_DISCOVER_RSP
N
CI_PROPRIETARY_ACT_RSP
F
ig 27. Initialization sequence to prepare the PN7150 operation (Reset configuration)