User's Manual
Table Of Contents
- 1. Introduction
- The PN7150 architecture overview
- 2. NCI Overview
- 3. DH interface
- 5. Initialization & Operation configuration
- 6. Reader/Writer Mode
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 6.1.1 Access through the [NCI] Frame RF Interface
- 6.1.2 [PN7150-NCI] extension: TAG-CMD Interface
- 6.1.3 [PN7150-NCI] extension: Payload structure of the TAG-CMD RF Interface
- 6.1.4 [PN7150-NCI] extension: REQs & RSPs rules
- 6.1.5 [PN7150-NCI] extension: List of REQs & RSPs
- 6.1.6 [PN7150-NCI] extension: raw data exchange REQs & RSPs
- 6.1.7 [PN7150-NCI] extension: T2T & MFU REQs & RSPs
- 6.1.8 [PN7150-NCI] extension: MIFARE Classic REQs & RSPs
- 6.1.9 Access through the TAG-CMD RF Interface
- 6.2 T3T tag
- 6.3 T4T & ISO-DEP Tags/Cards
- 6.3.1 Access through the Frame RF Interface
- 6.3.2 Access through the ISO-DEP RF Interface
- 6.3.3 [PN7150-NCI] extension: Presence check Command/Response
- 6.3.4 [PN7150-NCI] extension: S-Block Command/Response
- 6.3.5 [PN7150-NCI] extension: WTX notification
- 6.3.6 [PN7150-NCI] extension: Higher bit rates in Poll NFC-A & NFC-B
- 6.4 [PN7150-NCI] extension: 15693 & I-Code tags
- 6.5 [PN7150-NCI] extension: KOVIO tags
- 6.1 T1T, T2T, MIFARE Ultralight, MIFARE Classic and MIFARE Plus tags
- 7. Card Emulation Mode
- 8. P2P Initiator & Target Mode
- 9. RF Discovery Management
- 9.1 RF Discovery functionalities
- 9.2 NFC FORUM Profile as defined in [NCI]
- 9.3 [PN7150-NCI] extension: additional technologies not yet supported by the NFC FORUM
- 9.4 [PN7150-NCI] extension: Low Power Card Detector (LPCD) Mode
- 9.5 [PN7150-NCI] extension: EMVCo Profile in Poll & Listen Modes
- 9.6 [PN7150-NCI] extension: Power optimization
- 10. Configurations
- 11. Test Mode
- 12. PN7150 Practical approach
U
M10936
P
N7150 User Manual
UM
10936 All information provided in this document is subject to legal disclaimers.
U
ser manual
CO
MPANY PUBLIC
Rev. 2.0 — 6 November 2020
348120
3 of 127
1
. Introduction
The PN7150 is a full features NFC controller for contactless communication at
13.56 MHz.
The User Manual describes the software interfaces (API), based on the NFC FORUM
standard, NCI.
N
ote: this document includes cross-references, which can be used to directly access the
s
ection/chapter referenced in the text. These cross-references are indicated by the
following sign: ‘→’. This sign is positioned right before the section/chapter reference. The
way to jump to the referenced section/chapter depends on the file format:
• I
n the word format, you have to first press the key “Ctrl” on the key board and then
to click on the section/chapter reference number pointed by the ‘→’ sign. The
mouse symbol changes to a small hand when it is positioned on the
section/chapter reference number.
• In .pdf format, you only have to click on the section/chapter reference number
pointed by the ‘→’ sign: the mouse symbol automatically changes to a small hand
when it is positioned on the section/chapter reference number
As this document assumes pre-knowledge on certain technologies please check section
→15: References to find the appropriate documentation.
For further information please refer to the PN7150 data sheet [PN7150_DS].
In this document the term „MIFARE card“ refers to a contactless card using an IC out of
the MIFARE Classic, MIFARE Plus, MIFARE Ultralight or MIFARE DESFire product family