Instruction Manual
Table of Contents SECTION PAGE # SECTION 1: IMPORTANT SAFEGUARDS 1 SECTION 2: UNPACKING 3 SECTION 3: TOTAL BLENDER OVERVIEW 4 SECTION 4: INSTALLATION 4 SECTION 5: CARE AND CLEANING 6 SECTION 6: OPERATIONAL OVERVIEW 7 SECTION 7: TROUBLESHOOTING 8 SECTION 8: WARRANTY 10
SECTION 1 IMPORTANT INFORMATION Read all instructions carefully before using your TOTAL BLENDER™ 1.1 SAFETY CERTIFICATION The blender is certified by ETL (Report No. 30182044, 3018204-2 & 3018204-3). 1.2 TOTAL BLENDER CERTIFICATION TOTAL BLENDER and its accessories are certified by NSF International (NSF), under the letter K (for K-TEC) in the NSF Official Listing. R 1.3 AVOID CONTACT WITH MOVING PARTS • Keep fingers, hands, hair and clothing away from all moving parts.
1.8 NEVER OPERATE THE BLENDER USING ATTACHMENTS NOT SOLD BY BLENDTEC The use of any unauthorized attachments may cause fire, electric shock, and/or injury and will void the warranty. 1.9 CONTAINER MUST BE PROPERLY IN PLACE WHILE APPLIANCE IS OPERATING 1.10 BLADES ARE SHARP! HANDLE CAREFULLY! 1.11 WHEN BLENDING HOT LIQUIDS, REMOVE CENTER PIECE OF LID 1.12 POWER CORD PRECAUTIONS • NEVER operate with a damaged cord or plug.
SECTION 3 TOTAL BLENDER OVERVIEW (Refer to Figures 1 and 2) 3.1 BLENDER MOTOR • Motor Cover: Houses the power unit in a durable, easy-to-clean polycarbonate. • Touch Pad: Consists of six buttons that contain pre-programmed settings for selective blender control, a pulse button, and two speed control buttons. • LCD Information Center: will indicate status of unit as well as overload or over-temperature conditions.
SECTION 5 SECTION 6 CARE AND CLEANING OPERATIONAL OVERVIEW 5.1 AFTER USE CLEANING 1. Add 1 cup of hot water and a drop of liquid dishwashing soap to the blender jar. 2. Place the lid tightly onto the jar. Place the blender jar on the blender base, and with your hand placed on top of the lid; press the pulse button for 5 seconds. 3. Rinse with clear water until all soap is rinsed from jar and lid. 4. Clean the blender base by simply wiping the base and touchpad with a damp rag and water. 6.
SECTION 7 TROUBLESHOOTING 7.1 BLENDER MOTOR WILL NOT TURN ON If the blender motor will not turn on, try the following: • Make sure the main power switch on the back lower-right corner is turned ON. • Check your house circuit breaker switch or fuse, to make sure it is set to the ON position. • Unplug the power cord from the wall receptacle, wait 5 seconds, then plug power cord back in. • Determine if the Liquid Crystal Display (LCD) is lit. An absence of a lit LCD indicates a lack of power to the unit.
SECTION 8 WARRANTY WARRANTY DESCRIPTION (US Domestic and Canada) Your Blendtec Total Blender motor is warrented for 3 years or 10,000 cycles, whichever happens first. The jar assembly, including all moving jar parts, is covered against leaking or breakage for 1 year. The blender jar blade and the motor base drive socket are covered by a lifetime warranty. Warranties begin from date of purchase. The quality of Blendtec blenders are unsurpassed.
1206 South 1680 West Orem, UT 84058 801-222-0888 blendtechome.com 21-801-03 Blendtec Home Total Blender Manual Rev. 02 June 2006 ©2006 K-TEC, Inc., All Rights Reserved Blendtec is a registered trademark of K-TEC, Inc.
