K 2.080 Operating Instructions Before first use of the unit read these operating instructions and act in accordance with them. R e w gis w w. te ka r a er n ch d er .
Contents General information Description of the Appliance Safety instructions Operation Transport Storage Maintenance and care Troubleshooting Technical specifications Customer Service Spare Parts Symbols on the machine 2 3 4 6 8 8 9 9 10 10 11 General information Dear Customer, Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners.
Description of the Appliance 1 2 3 4 5 6 7 8 High pressure connection Detergent suction hose (with filter) Appliance switch "0/OFF“/ „I/ON“ Carrying handle Storage for mains connection cable Storage for spray lance Storage for high-pressure hose Mains cable with mains plug 9 10 11 12 13 14 15 Connection for water supply with filter Coupling element for water connection Trigger gun Lock trigger gun Clamp for high pressure hose High pressure hose Spray lance with high pressure nozzle English 3
Safety instructions Danger Never touch the mains plug and the socket with wet hands. The appliance must not be used if the power cord or important parts of the appliance, e.g. high-pressure hoses, trigger gun or safety devices are damaged. Check the power cord and mains plug for damage before every use. If the power cord is damaged, please arrange for it to be replaced immediately by an authorised repair agent or a skilled electrician Check the high-pressure hose for damage before every use.
Wear protective clothing and safety goggles to protect against splash back containing water or dirt. Caution In case of extended downtimes, switch the appliance off at the main switch / appliance switch or remove the mains plug. Do not operate the appliance at temperatures below 0 °C. Observe a distance of at least 30 cm when using the jet to clean painted surfaces to avoid damaging paintwork. Never leave the appliance unattended when it is in operation.
Operation Before Startup Illustrations on Page 3 Illustration Î Pull out the clamp for the high-pressure hose from the trigger gun (e.g. a small screwdriver). Illustration Î Connect high pressure hose to trigger gun. Î Push the clamp in until it locks. Check the secure connection by pulling on the high-pressure hose. Water supply Î Push the water supply hose onto the coupling unit, then connect it to the water supply.
Î Pull on the lever of the trigger gun; the device will switch on. Note: Release the lever of the trigger gun; the device will switch off again. High pressure remains in the system. Spray lance with high pressure nozzle For normal cleaning tasks. Not suitable for use with detergents. STEP 4: Î Connect the high pressure nozzle and press the hand trigger to begin cleaning. Start up Caution Dry runs lasting longer than two minutes lead to damages to the high pressure pump.
Finish operation Storage Caution Only separate the high-pressure hose from the trigger gun or the appliance while there is no pressure in the system. Î After working with detergent, suspend detergent suction hose in a container filled with clear water, switch the appliance on for around 1 minute once the spray lance has been removed and rinse until water runs clear. Î Release the lever on the trigger gun. Î Turn off the appliance "0/OFF". Î Turn off tap. Î Detach the appliance from the water supply.
Maintenance and care Danger Turn off the appliance and remove the mains plug prior to any care and maintenance work. Care Prior to longer periods of storage, e.g. in the winter: Î Remove filter from suction hose for detergent and clean under running water. Î Pull out the sieve in the water connection using flat-nose pliers and clean under running water. Maintenance The appliance is maintenance-free. Spare parts Use only original KÄRCHER spare parts.
Technical specifications Electrical connection Voltage Power consumption 220-240 V 1~50/60 Hz 6A Protection class IP X5 Protective class II Mains fuse (slow-blow) 10 A Water connection Max. feed temperature 40 °C Max. feed pressure 1,2 MPa Min. feed volume 8 I/min Performance data Working pressure Max.
Spare Parts English 11
