User manual

51
In this fully integrated appliance the controls are located on the
top of the door. When selecting a programme, the door needs
to be open.
1. Check that the baskets have been
loaded correctly and that the spray
arms can rotate freely
2. Turn on the water tap
3. Press the On/Off push button
The indicator lights of all the push buttons illuminate
(setting mode).
4. Setting and starting the programme
Press the push button of the programme you wish to
select. (See "Washing programmes" chart).
The corresponding indicator light illuminates and in the
digital display will flash the running time of the programme.
The start of the programme will occur only after the
closure of the door until that moment it is possible to
change the setted programme by pressing another
washing programme push button.
Close the door, the programme will start automatically. In
the digital display appears the running time of the
programme.
A point-shaped optical signal appears on the floor beneath
the dishwasher’s door. This optical signal will remain
illuminated for all the duration of the washing programme.
If the appliance has been installed higher up with a
furniture door mounted flush, the optical signal will be no
longer visible.
5. To interrupt or cancel a washing
programme
Interrupt or cancel a washing programme in progress
ONLY if it’s absolutely necessary.
Attention! Hot steam may escape when the door is
opened. Open the door carefully.
To interrupt a washing programme
● Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the
point in which it was interrupted.
To cancel a washing programme in progress
● Open the door. Press simultaneously the function push
buttons 2 and 3 for about 2 seconds, the indicator light
of the running programme will flash for about 2 seconds.
After about 2 seconds all the indicator lights will
illuminate indicating that the washing programme has
been cancelled and the machine is now in setting mode.
6. End of the washing programme
The dishwasher will automatically stop and an audible
signal informs you of the end of the washing programme.
When the wash programme has ended, the optical signal
on the floor beneath the dishwasher’s door will turn off.
Open the dishwashers’s door only when this optical
signal turns off.
If the door is not immediately opened at the end of the
programme, air will circulate inside the dishwasher to
prevent residual steam recondensing on the dishes as
water droplets.
This device operates intermittently for about 20
minutes, as long as the dishwasher is switched on.
If the On/Off push button is pressed or the door is opened
during these 20 minutes, the device will be automatically
cancelled.
Open the door and wait a few minutes before removing
the dishes; in this way they will be cooler and the drying
will be improved.
Switch off the dishwasher by pressing the On/Off push
button.
Water may appear on the sides and door of the
dishwasher as the stainless steel will eventually become
cooler than the dishes.
7. Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should
therefore be allowed to cool down before removing from
the appliance.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and
the water tap turned off.
"3 in 1" function
This function can be selected together with all
programmes (except the "Rinse and Hold" programme).
Place the 3 in 1 combi detergent tablet in the detergent
dispenser.
Press the "On/Off" push button, the On/Off indicator light
illuminates.
Press the 3 in 1 function push button, the correspondent
indicator light illuminates. Remember that if this function is
selected, it will remain active also for the following
programmes, until it will be deactivated by pressing the 3
in 1 function push button (indicator light off).
Select the required washing programme, after about 3
seconds the programme will start automatically.
Once the programme is running, the 3 in 1 function can
NO longer be changed. If you want to exclude the 3 in 1
function you have to cancel the programme setting (see
"To cancel a washing programme in progress") and then
deactivate the 3 in 1 function by pressing the 3 in 1 push
button.
In this case you have to set a washing programme again.
With the use of 3 in 1 combi detergent tablets, the cycle
durations given in the "Washing programmes" chart may
change.
Starting a washing programme