Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 69-2021TP Typhoon Air Intake Kit, Short Ram, Polished

69-2021TP

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

PARTS LIST

Description Qty. Part #

2. Using a pair of dikes or pliers unclip the stock

hose clamp at the air cleaner as shown.

3. Pull the stock intake tube off the air cleaner as

shown.

4. Pull upward to remove the battery terminal from

the side of the air cleaner as shown.

5. Loosen the two bolts on the front of the air

cleaner assembly as shown.

6. Slide the upper air cleaner assembly backwards,

then, pull upward to remove the upper air cleaner

assembly as shown.

7. Using a pair of dikes or pliers unclip the hose

clamp on the air inlet duct as shown.

8. Remove the air cleaner inlet duct as shown.

9. Remove the throttle body electrical connection

as shown.

TOOLS NEEDED:

Pliers

Flat Blade Screwdriver

10mm Wrench

4mm Allen Wrench

Ratchet

6” Extension

8mm Socket

10mm Socket

MINI

2002-06 Cooper S

2007 Cooper S (Convertible only)

L4-1.6L Supercharged

A Hose Clamp #40 4 08554

B Silicone Hose, Black 1 08284

C Intake Tube 1 27122

D 6mm Wave Washer 1 08277

E 6mm Bolt, 12mm L 1 07727

F 6mm Rubber Stud 1 07027

G 6mm Nylock Nut 2 07512

H 6mm Flat Washer 2 08269

I “Z” Bracket 1 070058

J 5mm Flat Washer 2 08212

K #10 Screw 2 07747

L Heat Shield 1 07301

M Edge Trim 9” L 1 102465

N Air Filter 1 RU-4950

O Tube; “B”, 2-1/2”OD X 8”L 1 27123

P Plug; 1/4 NPT, Plastic 1 08032

Q Vent; Strt 1/2” Hose, 1/4”NPT 1 080022

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED

HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

NOTE: C.A.R.B. E.O. # D-269-30 APPLIES

ONLY To 2002-2004 Model Year Vehicles

Summary of content (3 pages)

PAGE 1
® 69-2021TP TOOLS NEEDED: Pliers Flat Blade Screwdriver 10mm Wrench 4mm Allen Wrench Ratchet 6” Extension 8mm Socket 10mm Socket MINI 2002-06 Cooper S 2007 Cooper S (Convertible only) L4-1.6L Supercharged NOTE: C.A.R.B. E.O.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 10. Using a pair of dikes or pliers, unclip the stock hose clamp on the stock intake tube at the throttle body as shown. 11. Pull upward on the stock intake tube, then, using a pair of pliers disconnect the stock crank case vent hose from the stock intake tube as shown. NOTE: Some models may be equipped with a second vent line, which will also need to be disconnected. 15. Install the provided edge trim onto the K&N® heat shield as shown. 20.
PAGE 3
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fix as necessary. 25.