Installation Manual

ManualsBrandsK&N ManualsAutomotiveK&N 69-1209TS Silver Performance Intake Kit

TO START:

1. Turn the ignition off and disconnect the vehicle’s

negative battery cable.

NOTE: Disconnecting the negative battery

cable erases pre-programmed electronic

memories. Write down all memory settings be-

fore disconnecting the negative battery cable.

Some radios will require an anti-theft code to

be entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

Flat Blade Screwdriver

Phillips Screwdriver

Ratchet

Extension

13mm Socket

10mm Socket

5.5mm Socket

2.5 mm Allen Wrench

4mm Allen Wrench

10mm Wrench

69-1209TS

Description Qty. Part #

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

2. Depress the locking tab and remove the mass

air sensor connector. Remove the clips securing

the mass air sensor harness to the stock airbox

and intake tube.

3. Depress the spring clamp and remove the crank-

case vent line from the vent chamber on the stock

intake tube. Disconnect the vent hose from the

stock intake tube.

4. Loosen the hose clamp at the throttle body and

unclip the throttle position sensor harness from the

stock intake tube.

5. Pull rmly to remove the stock intake tube from

the airbox. Remove the intake tube from the

vehicle.

6. Remove the two bolts securing the stock airbox

to the vehicle.

HONDA

2004-07 Accord

L4-2.4L (SULEV ONLY)

A Hose Clamp #40 2 08554

B Hose; 2-3/4" ID X 2"L, 1 08440

C Intake Tube 1 27534

D Hose; 1-1/8" ID X 2"L 1 084074

E Hose Clamp #16 2 08413

F Bolt; M4- 0.07 8MM, A/H Cap, 2 07733

G Heat Shield 1 07353

H Edge Trim 1 102494

I Hose Clamp #44 1 08577

J Air Filter 1 RU-4870

K Bracket; "Z", STL, FB/PC 1 06498

L Bolt; 6MM - 1.00 X 16MM, 2 07812

M Washer; 1/4" Lock, ZN 2 08198

N Washer; 1/4"IDx5/8"OD-SAE 8 08275

O Bolt; 8MM-1.25x16mm, hex 1 07844

P Washer; 8MM Spring (Wave) 1 08239

Q Washer; 5/16"IDx5/8"OD 1 08276

R Bracket; "L", STL, FB/PC 1 06499

S Bolt; M6x1.00x16mm Btnhd 3 07730

T Nut; 6MM Nylock, Hex Head 3 07512

U Bracket; "L", STL, FB/PC 1 06497

V Hose Mender; 1/2" Barbed 1 08686

W Hose; 1/2" ID X 7"L, 1 08159

X Hose Clamp #004 2 21850

Y Hose; 5/16"IDx17-1/4"L 1 5-2017

TOOLS:

PARTS LIST

Summary of content (3 pages)

PAGE 1
® 69-1209TS HONDA 2004-07 Accord L4-2.4L (SULEV ONLY) H TOOLS: E Flat Blade Screwdriver Phillips Screwdriver Ratchet Extension 13mm Socket 10mm Socket 5.5mm Socket 2.5 mm Allen Wrench 4mm Allen Wrench 10mm Wrench D F I E C A K B QP O A M T N X PARTS LIST A B C D E F G H I X Description Hose Clamp #40 Hose; 2-3/4" ID X 2"L, Intake Tube Hose; 1-1/8" ID X 2"L Hose Clamp #16 Bolt; M4- 0.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Unclip the wiring harness from the bottom of the stock airbox and remove from the vehicle. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake. 8. Depress the spring clamp and remove the crankcase vent hose from the valve cover. 12. Install the provided silicone hose (#08440) onto the throttle body. Secure with the provided hose clamp as shown. 17.
PAGE 3
Continued INSTALLATION INSTRUCTIONS 22. Install the K&N® intake tube into the silicone hose at the throttle body and align with the tube mounting bracket installed in step # 13. Secure with the provided hardware and hose clamp. 27. Install the crankcase chamber assembly onto the K&N® intake tube and valve cover. Secure with the provided hose clamp. NOTE: Some trimming of the ½” silicone hose may be necessary. 31. Reconnect the vehicle's negative battery cable.