Installation Manual

ManualsBrandsK&N ManualsAir IntakeK&N Performance Air Intake Kit 63-3082 with Black HDPE Tube and Lifetime Red Oiled Filter for Escalade, Silverado 1500, Suburban, Tahoe, Sierra, Yukon, Denali, XL

63-3082

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

NOTE: This kit was not designed

to t vehicles with a body lift.

Description Qty. Part # Description Qty. Part # Description Qty. Part #

A Hose Clamp #56 1 08620

B Hose; 4"ID To 3.5"ID X 3"L TPRD 1 08497

C Hose Clamp #64 Stainless 4 08645

D Hose; 5/8" ID X 14"L 2 084083

E Vent; STRT, 5/8 Barbed 1/4 NPT 2 08911

F Intake Tube 1 087268

G Gasket; 57-2556, 3/16 poron 1 09069

H Adaptor; 57-2556, Nylon 6/6 GF 1 21515

I Bolt; M4-0.07 8MM, A/H Cap, SS 2 07733

J Washer; 6MM Flat, SS 4 08269

K Bolt; M6 X 1.00 X 16MM, SS 4 07730

L Hose; 4"ID X 3"L Hump 2 08418

M Washer; M6 Split Lock Zinc 2 1-3025

N Edge Trim (44") 1 102486

O Heat Shield 1 073155-1

P Adapter; Universal, 6" Filter 1 27300

Q Hose Clamp #104 1 08697

R Air Filter 1 RF-1041

PARTS LIST:

TOOLS NEEDED:

ratchet

extension

10mm socket

at blade screw driver

T10 TORX

4mm allen key

3mm allen key

¾” wrench.

2. Disconnect the mass air sensor electrical

connection.

3. Disconnect the two crank case vent tubes from

the intake plenum.

4. Loosen the two hose clamps securing the intake

plenum to the factory air box and to the throttle

body.

5. Remove the intake plenum from the vehicle.

6. Pull up the air box to release it from the

mounting grommets and then remove the factory

air box from the vehicle.

NOTE: It will be necessary to unhook the mass

air sensor wiring harness from the air box as it

is removed.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

7. Remove the four bolts securing the air box

mounting tray and then remove the tray from the

vehicle.

NOTE: Three of the bolts will be reused in a

latter step.

CHEVROLET / GMC / CADILLAC

2014 Silverado 1500 / Sierra 1500

2015 Tahoe / Suburban / Yukon / Escalade ESV

V8-5.3L / 6.2L

Summary of content (3 pages)

PAGE 1
63-3082 CHEVROLET / GMC / CADILLAC 2014 Silverado 1500 / Sierra 1500 2015 Tahoe / Suburban / Yukon / Escalade ESV V8-5.3L / 6.2L D F E C NOTE: This kit was not designed to fit vehicles with a body lift. L E C TOOLS NEEDED: ratchet extension 10mm socket flat blade screw driver T10 TORX 4mm allen key 3mm allen key ¾” wrench. N M D B K C G I Q R K J H M J A P L O PARTS LIST: Description C Qty. Part # Description Qty. Part # Description Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 8. Install the provided edge trim onto the heat shield as shown. NOTE: Some trimming of the edge trim will be necessary. 9. Install the heat shield assembly and secure the air box mounting plate location using the three factory bolts from step #7. 10. Install the filter adapter into the K&N® air filter and secure with the provided hose clamp. 13. Install the coupling hose (08497 for 5.3L, 08418 for 6.2L) onto the throttle body and secure with the provided hose clamp.
PAGE 3
Continued INSTALLATION INSTRUCTIONS ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fix as necessary. 23.