Installation Manual

ManualsBrandsK&N ManualsAir IntakeK&N 63-3078 AirCharger Performance Air Intake System

63-3078

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED

HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery

cable erases pre-programmed electronic

memories. Write down all memory settings be-

fore disconnecting the negative battery cable.

Some radios will require an anti-theft code to

be entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

PARTS LIST:

Description Qty. Part #

CHEVROLET

Camaro 2011-14

V6-3.6L

10mm Socket

13mm Socket

3mm Allen Wrench

4mm Allen Wrench

Extension

Flat Blade Screwdriver

Ratchet

2. Remove the oil ll cap, lift up and

remove the engine cover. Reinstall the oil cap.

3. Slide the red locking tab back and then discon-

nect the mass air sensor electrical connection.

4. Disconnect the crank case vent hose from stock

intake tube.

5. Loosen the hose clamp that secures the intake

hose to the throttle body.

6. Unlatch the upper air box clips and remove the

upper air box and intake tube assembly.

7. Remove the lower air box mounting nuts, then

remove the lower air box assembly.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

8. Remove the air box mounting grommet shown

on the frame rail.

A Hose Clamp #48 1 08601

B Hose; 3-1/4” To 3” ID 90 DEG 1 08629

C Hose Clamp #56 2 08620

D Intake Tube 1 087256

E Gasket; 3/16 Poron 1 09074

F Adapter; Mass Air Sensor 1 09404

G Adaptor; Nylon 6/6 GF, Black 1 21515

H Gasket; 3/16 Poron 1 09069

I Bolt; M4-0.07 8mm, A/H Cap, SS 2 07733

J Bolt;M6 X 1.00 X 116mm, ButtnHd, SS 6 07730

K Washer; 6mm Flat, SS 2 08269

L Vent; STRT 1/2” Hose, 1/4” NPT, Plas. 1 080022

M Hose; 1/2” ID X 3-1/2”L 1 087028

N Hose Clamp #52 1 08610

O Hose; Hump 3.25/3.50 X 3.00 1 5-576

P Washer; 1/4” Lock, ZN 2 08198

Q Washer; 1/4”ID X 5/8”OD-SAE 7 08275

R Edge Trim (70”) 1 102454

S Heat Shield 1 074053

T Insert; 5/16-18 X .600 OD X .730L Rubber 1 088002

U Bracket; “Z” , STL, TK/PC 1 083126

V Washer; 5/16” ID X 5/8” OD, Flat 1 08276

W Bolt; 5/16”-18 X 1” L, SS 1 07777

X Nut; 6mm Nylock, Hexhead 3 07553

Y Washer; 1” X .300 X 1.00 Rubber 1 21685

Z Adapter; Universal, 6” Filter 3.5” Coupler 1 21512-1

AA Hose Clamp #104 1 08697

BB Air Filter 1 RC-5107

Summary of content (3 pages)

PAGE 1
63-3078 B CHEVROLET A Camaro 2011-14 V6-3.6L M C L TOOLS NEEDED: 10mm Socket 13mm Socket 3mm Allen Wrench 4mm Allen Wrench Extension Flat Blade Screwdriver Ratchet R N O D C H J G E K J F X P J P J I Q Q Q Y Q X Q PARTS LIST: Description A B C D E F G H I J K L M N Hose Clamp #48 Hose; 3-1/4” To 3” ID 90 DEG Hose Clamp #56 Intake Tube Gasket; 3/16 Poron Adapter; Mass Air Sensor Adaptor; Nylon 6/6 GF, Black Gasket; 3/16 Poron Bolt; M4-0.07 8mm, A/H Cap, SS Bolt;M6 X 1.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 9. Install the heat shield mounting bracket (083126) onto the heat shield and secure with the provided hardware. 15. Install the heat shield assembly into the vehicle so the inserted nut goes into the air box mounting grommet hole and the tab goes onto the air box mounting stud. Secure the heat shield with the provided hardware. 18. Install the mass air sensor into the mass air sensor adapter and secure with the provided hardware.
PAGE 3
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 22. Remove the 90° vent hose from the crank case vent tube.