Owners manual

A
B
C
D
C
E
F
G
Stock mass air sensor
H
J
K
L
M
N
M
I
P
Q
H
L
O
77-3023KP
CHEVROLET / GMC / CADILLAC
TOOLS NEEDED:
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE
MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
PARTS LIST:
Description Qty. Part #
NOTE: This kit was not designed to t
vehicles with a body lift.
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery
cable erases pre-programmed electronic
memories. Write down all memory settings be-
fore disconnecting the negative battery cable.
Some radios will require an anti-theft code to
be entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner’s manual. In the event your vehicles’
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
2. Disconnect the mass air sensor electrical
connection as shown.
6. Pull rmly upwards to remove the air cleaner as-
sembly as shown.
NOTE: K&N Engineering, Inc., recommends that
customers do not discard factory air intake.
Silverado Classic 1500 HD
Sierra Classic 1500 HD
2007 V8-6.0L
Silverado 1500 HD
Sierra 1500 HD
2005-06 & 2001-03 V8-6.0L
Silverado 2500 / Sierra 2500
1999-04 V8-6.0L
1999-00 V8-5.3L
Silverado Classic SS
2007 V8-6.0L
Silverado SS
2003-04 V8-6.0L
Tahoe / Yukon
2000-2004 V8-4.8L, 5.3L
Avalanche 1500
2002-04 V8-5.3L
Suburban
2005-06 V8-6.0L
2000-04 V8-6.0L, 5.3L
Sierra Classic Denali
2007 V8-6.0L
Sierra Classic Denali
2002-04 V8-6.0L
Sierra C3
2001 V8-6.0L
Yukon XL
2005-06 V8-6.0L
2000-04 V8-6.0L, 5.3L
Yukon Denali / Yukon XL Denali
2001-04 V8-6.0L
Escalade
2002-04 V8-6.0L, 5.3L
Escalade EXT
2002-04 V8-6.0L
Escalade ESV
2003-04 V8-6.0L
Flat blade Screwdriver
Ratchet
10mm Socket
4mm Allen Wrench
A Angled Silicone Hose 1 084053
B Hose Clamp, #64 1 08645
C Hose Clamp, #56 2 08620
D Performance Intake Tube 1 27141
E Silicone Hump Hose 1 084056
F Hose Clamp, 56 1 08620
G Bolt, M5-.80, 20mm L. C/H/A 3 08320
H Gasket, 1/16” Neoprene 2 09033
I Edge Trim, 48” L. 1 102485
J Heat Shield 1 07316
K Nut, 6mm Nylock 2 07512
L Washer, Fender 2 08160
M Washer, Rubber 2 21685
N Rubber Mounted Stud, 6mm 2 07027
O Adapter, Mass Air 1 08783
P Hose, Clamp, #104 1 08697
Q Air Filter 1 RC-5046
3. Loosen the hose clamps at the throttle body and
at the mass air sensor.
4. Unclip the radiator hose from the intake tube as
shown.
5. Disconnect the stock intake tube from the mass
air sensor and from the throttle body, then, remove
the intake tube as shown.
7. Loosen the hose clamp on the air cleaner then
remove the mass air sensor as shown.
8. Remove the two stock air cleaner support tray
bolts as shown.