Owners manual

ManualsBrandsK&N Filters ManualsAutomotive71-3535 Blackhawk Air Induction Kit Fits 15-17 Mustang

71-3535

1. Turn o the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

FORD

2015-17 Mustang GT

V8-5.0L

Description Qty. Part # Description Qty. Part # Description Qty. Part #

A HOSE CLAMP #56, BLACK ZINC 4 08620K

B HOSE; 3-1/2" ID X 2-1/2" L 2 08699

C INTAKE TUBE 1 27640TK

D BOLT; M4 - 0.07 8MM, A/H CAP 2 07733

E MAF EXTENSION HARNESS 1 21780

F CABLE TIES; 11" BLACK 1 21590

G CAPLUG; 15/16" ID, 3/4" L, BLK 1 08246

H EDGE TRIM (66") 1 102472

I BOLT; M6 X 1.00 X 16MM ,SS 2 07730

J WASHER, M6 SPLIT LOCK ZINC 5 1-3025

K WASHER; 6MM FLAT, SS 5 08269

L HEAT SHIELD 1 073180

M BOLT; M6 X 1.00" X 20MM HEX 2 07795

N BRACKET; 'L", 63-2589, STL 1 064325

O BOLT; 8MM-1.25 X 16MM 1 07844

P WASHER, M8 SPLIT LOCK ZINC 1 1-3036

Q WASHER; 8MM, FLAT, SS 1 08272

R BRACKET; SMALL "L", 63-2589 1 064326

S SPACER: .625" OD X .250"ID 1 06555

T BOLT; 6MM-1.00 X 16MM, SS 1 07812

U ADAPTER; UNIVERSAL, 6" 1 21512-1

V HOSE CLAMP #44, BLACK ZINC 1 08560K

W FILTER CHARGER 1 RU-3106HBK

X TIP; 3/8”OD X 1/4”ID X 1-1/4”L 1 08215

PARTS LIST:

TOOLS NEEDED:

at blade screw driver

ratchet

extension

13mm socket

10mm socket

pliers

T20 torx

3mm allen

2. Lift up the decorative engine cover to dislodge

it from the mounting studs and then remove the

engine cover from the vehicle.

3. Depress the locking tab and then disconnect the

idle bypass hose from the intake tube.

4. Depress the locking tabs and then disconnect

the crank case vent hose and the EVAP vent hose.

Then release the spring clamp and disconnect the

sound tube from the intake tube.

NOTE: Some vehicles are not equipped with the

EVAP vent hose.

5. Cut the clamp that secures the sound tube/

chamber to the sound drum and then disconnect

the sound tube/chamber from the sound drum.

6. Install the provided cap onto the sound drum.

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Summary of content (3 pages)

PAGE 1
71-3535 A B FORD A 2015-17 Mustang GT V8-5.0L H D X C TOOLS NEEDED: J flat blade screw driver ratchet extension 13mm socket 10mm socket pliers T20 torx 3mm allen I K A A I F E T J B M K S K R J U K V G W M K J L P O Q PARTS LIST: Description N Qty. Part # Description Qty. Part # Description Qty. Part # A HOSE CLAMP #56, BLACK ZINC 4 08620K I BOLT; M6 X 1.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Release the locking tab and then disconnect the mass air sensor electrical connection. 8. Remove the bolt securing the air filter assembly onto the inner fender. 9. Loosen the hose clamp securing the intake tube to the throttle body and then remove the air filter assembly and intake tube from the engine compartment. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake. 10.
PAGE 3
Continued INSTALLATION INSTRUCTIONS 22. Connect the provided mass air sensor extension harness into the factory mass air sensor connection and then connect the other end to the mass air sensor. NOTE: Route the mass air sensor extension harness so that it cannot rub on sharp edges. Secure the harness with the provided tie wrap if necessary. 23. Reinstall the engine cover. 24. Reconnect the vehicle’s negative battery cable.