Owners manual

L
Y
X
W
A
B
D
C
E
A
A
A
K
A
J
F
G
H
I
FACTORY
MASS AIR
G
H
V
P
Q
N
O
U
H
H
S
M
M
T
R
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE
MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories.
Write down all memory settings before
disconnecting the negative battery cable. Some
radios will require an anti-theft code to be
entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner’s manual. In the event your vehicles’
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
NOTE: This kit was not designed
to t vehicles with a body lift.
Description Qty. Part # Description Qty. Part # Description Qty. Part #
A Hose Clamp #64, Black Zinc 5 08645K
B Hose; 4"ID To 3.5"ID X 3"L TPRD 1 08497
C Hose; 3/8"ID X 17"L 1 08404
D Hose Clamp #56, Black Zinc 1 08620K
E Intake Tube 1 27599TK
F Bolt; 6MM-1.00 X 16MM, SS 1 07812
G Washer; M6 Split Lock Zinc 3 1-3025
H Washer; 1/4"ID X 5/8"OD -SAE 6 08275
I Bracket; 57-3021, L-Bend, FIN 1 070812
J Hose; 3-5/8"ID X 3-3/8"L, Hump 1 08543
K Hose; 4" To 3-13/16" ID X 2"L 1 08618
L Bolt; M6 X 1.00 X 16MM, SS 2 07730
M Bolt; M6-1.00 X 25MM Hex HD 2 07704
N Washer; 5/16"ID X 5/8"OD, Flat 2 08276
O Insert; 5/16-18 X .600 OD X .730 2 088002
P Heat Shield 1 07635
Q Bolt; 5/16"-18 X 1"L, SS 2 07777
R Spacer; .625"OD X .250"ID 1 06555
S Washer; 1"D X 1/4 Hole Fender 2 08160
T Bracket; "L" Small, STL, TB/PC 1 010031
U Nut; 6MM Nylock, Hexhead, SS 2 07512
V Edge Trim (39") 1 102496
W Adaptor; 57-3058 #454 1 27300
X Hose Clamp #104, Black Zinc 1 08697K
Y Air Filter 1 RU-3102-HBK
PARTS LIST:
TOOLS NEEDED:
Flat Blade Screwdriver
3mm Allen Wrench 10mm
1/2” Socket
5/8” Wrench
Ratchet
Extension
Socket
Pliers
2. Disconnect the mass air sensor electrical
connection.
3. Lift up on the front of the engine cover to
disengage from the mounting grommets. Then pull
forward and remove the engine cover from the
engine as shown.
4. Unhook the radiator hose mount from the intake
tube.
5. Disconnect crank case vent hose from the valve
cover as shown.
6. Loosen the hose clamps which secure stock
intake tube to the throttle body and mass air sensor
and then remove the intake tube from the vehicle.
71-3058
CHEVROLET / GMC / CADILLAC
2007-08 Yukon Denali / Yukon XL Denali / Sierra Denali
Escalade / Escalade ESV / Escalade EXT
V8-6.2L
2007-08 Suburban / Yukon XL / Avalanche
V8-5.3L / 6.0L
2007-08 Silverado / Sierra
V8-4.8L / 5.3L / 6.0L
2007-08 Tahoe / Yukon
V8-4.8L / 5.3L