Owners manual

ManualsBrandsK&N Filters ManualsAutomotive71-1576 Blackhawk Air Induction Kit Fits 18-19 Wrangler

71-1576

1. Turn o the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

JEEP

2018 Wrangler JL

V6-3.6L

TOOLS NEEDED:

Flat blade screw driver

4mm allen

Ratchet

Extension

10mm socket

NOTE: This kit was not designed

to t vehicles with a body lift.

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Description Qty. Part # Description Qty. Part # Description Qty. Part #

A HOSE CLAMP; #52 3 08610

B HOSE; 3.25"ID X 2"L 1 08690

C INTAKE TUBE 1 27806TK

D GROMMET; 1"OD,1/2"ID,1/2" 1 08064

E HOSE; 3.25"ID TO 3"ID X 2"L 1 08186

F HOSE CLAMP; #48 1 08601

G BOLT; M6 X 1.00 X 16MM , BH 2 07730

H WASHER, M6 SPLIT LOCK ZINC 3 1-3025

I WASHER; 6MM FLAT, SS 3 08269

J HEAT SHIELD 1 073268

K EDGE TRIM (50") 1 102481

L SPACER;.313 ALUMINUM 1 KITSPACER05

M WASHER; 8MM, FLAT, SS 2 08272

N WASHER, M8 SPLIT LOCK ZINC 2 1-3036

O BOLT; M6 X 1.00" X 20MM HEX 1 07795

P STANDOFF; 6.0 FORD AIRBOX 2 06532

Q BOLT; 8MM-1.25 X 16MM, HEX 2 07844

R ADAPTER; FILTER, 3.0"OD 1 21569

S HOSE CLAMP; #80 1 08694

T FILTER CHARGER 1 RU-3107HBK

PARTS LIST:

2. Disconnect the inlet air temperature sensor

connection and unhook the wiring harness from the

intake plenum. Unhook the coolant by-pass hose

from the intake plenum and loosen the hose clamp

that secures the tube to the throttle body.

3. Remove the two bolts shown that secure the

intake tube to the core support. Push the white

locking for the crank case vent line down and then

disconnect the crank case vent line from the intake

tube.

4. Remove the bolt shown that secures the fresh

air intake duct to the fender, then lift and remove

the complete intake system from the vehicle.

NOTE: The factory mounting grommets should

remain in the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

5. Remove the inner bolt that attaches fender

bracket to the fender.

6. Install the provided coupler (08690) onto the

throttle body and secure with the provided hose

clamp.

Summary of content (2 pages)

PAGE 1
71-1576 A JEEP 2018 Wrangler JL V6-3.6L B A K C J L I H O H D I G F H PARTS LIST: T Description R S Qty. E A TOOLS NEEDED: Q N M P Flat blade screw driver 4mm allen Ratchet Extension 10mm socket Part # Description Qty. Part # Description Qty. Part # A HOSE CLAMP; #52 3 08610 H WASHER, M6 SPLIT LOCK ZINC 3 1-3025 O BOLT; M6 X 1.00" X 20MM HEX 1 07795 B HOSE; 3.25"ID X 2"L 1 08690 I WASHER; 6MM FLAT, SS 3 08269 P STANDOFF; 6.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Remove the temp sensor from the factory intake tube by gently lifting the tab and rotating the sensor counter clockwise. Once the sensor is removed, remove the sealing O ring from the sensor. NOTE: The temp sensor is very fragile, use care while handling. 11. Install the heat shield assembly into the vehicle so that the mounting studs insert into the factory mounting grommets. 15. Reconnect the vehicle’s negative battery cable.