Owners manual

ManualsBrandsK&N Filters ManualsAutomotive71-1533 Blackhawk Air Induction Kit Fits Ram 1500 Ram 2500 Ram 3500

71-1533

1. Turn o the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

NOTE: This kit was not designed

to t vehicles with a body lift.

DODGE

2003-08 Ram 1500 / 2500 / 3500

V8-5.7L

Description Qty. Part #

A HOSE CLAMP #56, BLACK ZINC 2 08620K

B HOSE 1 08698

C INTAKE TUBE 1 27643TK

D HOSE; 5/8" ID X 13" L 1 08602

E HOSE; 17/32" ID X 11/16" L 1 084054

F STUD; M6-1.00 M/M, RUB 6 07027

G BRACKET; ANGLED SMALL 1 070049

H WASHER; 6MM FLAT, SS 11 08269

I NUT; 6MM NYLOCK, HEXHEAD 12 07512

J EXTENSION HARNESS; IAT 1 21680

K HEAT SHIELD 1 07487

L BRACKET; ANGLED LARGE 1 070050

M WASHER; 1"D X 1/4 HOLE 2 08160

N WASHER; 1" X .300 X .100 RUB 2 21685

O BOLT; 6MM-1.00 X 16MM, SS 1 07812

P BRACKET; L-TWIST, STL, TB/PC 1 070048

Q EDGE TRIM (57") 1 102470

R HOSE CLAMP # 60 1 08624K

S FILTER CHARGER 1 RU-3105HPK

PARTS LIST:

TOOLS NEEDED:

Ratchet

Extension

8mm socket

10mm socket

13mm socket

Flat Blade Screw Driver

2. Loosen the hose clamp securing the factory

intake tube to the intake plenum.

3. Disconnect the crank case vent hose from the air

lter housing.

4. Lift up and remove the air lter housing and

intake tube from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

5. Disconnect the inlet air temperature sensor and

loosen the bolt securing the intake plenum.

6. Loosen the remaining bolt securing the intake

plenum.

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Summary of content (3 pages)

PAGE 1
71-1533 A DODGE B 2003-08 Ram 1500 / 2500 / 3500 V8-5.7L A C NOTE: This kit was not designed to fit vehicles with a body lift. D E TOOLS NEEDED: Ratchet Extension 8mm socket 10mm socket 13mm socket Flat Blade Screw Driver J PARTS LIST: Description K F G I I H F L H R S I H H M N F I H P F M I H OH N I H Q Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Remove the intake plenum and throttle body seal from the vehicle. 8. Release the spring clamp and then disconnect the crank case vent hose from the breather port. 13. Install the two of the rubber mounted studs onto the provided bracket (070050) and secure with the provided hardware. 19. Install the heat shield assembly into the vehicle and secure to the bracket previously installed, to the inner fender and rubber mounted stud. 14.
PAGE 3
INSTALLATION INSTRUCTIONS Continued 25. Install the provided coupling hose (08698) onto the throttle body and secure with the provided hose clamp. 26. Install the intake tube into the heat shield and coupling hose at the throttle body then secure the tube with the hose clamp and hardware, 28. Connect the provided extension harness to the factory inlet air temperature sensor harness and then connect the open end to the sensor installed into the K&N® intake tube. 30.