Owners manual

ManualsBrandsK&N Filters ManualsAutomotive69-7084TS Typhoon Cold Air Induction Kit Fits 17-18 Pathfinder QX60

69-7084TS

1. Turn o the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

NISSAN / INFINITI

2017-18 Pathnder / QX60

V6-3.5L

TOOLS NEEDED:

Flat Blade screw driver

Phillips screw driver

Ratchet

Extension

8mm socket

10mm socket

3mm allen

4mm allen

NOTE: This kit was not designed

to t vehicles with a body lift.

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Description Qty. Part # Description Qty. Part # Description Qty. Part #

A HOSE CLAMP; #52 3 08610

B HOSE; 3.25"ID X 2"L REIN 1 08690

C INTAKE TUBE 1 25804S

D BOLT; M4 - 0.07 8MM, A/H CAP 2 07733

E HOSE; 5/8"ID X 5"L 1 08538

F HOSE MENDER; 1/2" BARBED 1 08686

G HOSE; 3.5"ID TO 3.25"ID X 2.5"L 1 08496

H HOSE CLAMP; #56 1 08620

I BOLT; M6 X 1.00 X 16MM, SS 2 07730

J WASHER, M6 SPLIT LOCK ZINC 5 1-3025

K WASHER; 6MM FLAT, SS 5 08269

L BOLT; 6MM-1.00 X 16MM, SS 2 07812

M MOUNT, PLASTIC AIRBOX 2 8-186-1

N HEAT SHIELD 1 073261

O STUD; RUBBER MOUNT, M6 1 02033

P EDGE TRIM (61") 1 102492

Q BOLT; M6 X 1.00 X 12MM, SS 1 07727

R ADAPTER; UNIVERSAL, 6" 1 21512-1

S HOSE CLAMP; #104 1 08697

T FILTER CHARGER 1 RU-4600

PARTS LIST:

2. Remove the two bolts that secure the fresh air

duct and then remove the fresh air duct from the

vehicle.

3. Release the spring clamp and then disconnect

the negative battery cable.

4. Loosen the hose clamp that secures the factory

intake tube to the air lter housing.

5. Remove the bolt which secures the air lter

housing to the mount.

6. Partially remove the air lter housing to access

the transmission vent line, mass air sensor and

wiring harness, disconnect the mass air sensor and

wiring harness and trans mission vent line and then

remove the air lter housing from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

Summary of content (2 pages)

PAGE 1
® 69-7084TS NISSAN / INFINITI 2017-18 Pathfinder / QX60 V6-3.5L TOOLS NEEDED: Flat Blade screw driver Phillips screw driver Ratchet Extension 8mm socket 10mm socket 3mm allen 4mm allen A D A B A N L G P K J I JK Q J K C H I JK E F S T L J M R K O M PARTS LIST: Description Qty. Part # Description Qty. Part # Description Qty. Part # A HOSE CLAMP; #52 3 08610 H HOSE CLAMP; #56 1 08620 O STUD; RUBBER MOUNT, M6 1 02033 B HOSE; 3.
PAGE 2
INSTALLATION INSTRUCTIONS Continued 7. Loosen the hose clamp securing the factory intake tube to the throttle body and then remove it from the vehicle. 13. Install the K&N® filter adapter into the heat shield and secure with the provided hardware. 19. Reinstall the fresh air duct so it inserts slightly into the K&N® heat shield then secure with the factory hardware. 8.