Owners manual

69-5319TS
1. Turn o the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories.
Write down all memory settings before
disconnecting the negative battery cable. Some
radios will require an anti-theft code to be
entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owners manual. In the event your vehicles
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
®
KIA
2017-18 SOUL!
L4-1.6L Turbo
TOOLS NEEDED:
Ratchet
Extension
10mm socket
at blade screw driver
Pliers
NOTE: This kit was not designed
to t vehicles with a body lift.
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE
MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
If you need any assistance please call 1-800-858-3333 to speak with a representative
in our Customer Service Center before returning the product.
Description Qty. Part # Description Qty. Part # Description Qty. Part #
A HOSE CLAMP #44 STAINLESS 2 08560
B HOSE; HUMP 2.75"ID X 2.5"L 1 08185
C INTAKE TUBE 1 25800S
D VENT; STRT, 1/2" HOSE, 1/4" 1 080022
E HOSE; 1"ID X 11"L, W/ 1"L 1 08479
F FITTING; VENT STRT, 1" X 1” 1 08296
G HOSE CLAMP #48 2 08601
H HOSE; HUMP 3"ID X 2.5"L 1 087121
I BOLT; M6 X 1.00 X 16MM, SS 2 07730
J WASHER, M6 SPLIT LOCK ZINC 5 1-3025
K WASHER; 1/4"ID X 5/8"OD 11 08275
L HEAT SHIELD 1 073255
M BRACKET; "L", 63-5317, STL. 1 064347
N STUD; RUBBER MNT, M/F, 1/2"L 1 070228
O BOLT; 6MM-1.00 X 16MM, SS 2 07812
P BOLT; M6 X 1.00" X 20MM HEX 3 07795
Q SPACER; .625" OD X .250"ID 4 06555
R NUT; 6MM NYLOCK, HEXHEAD 3 07512
S EDGE TRIM (35") 1 102471
T CABLE TIES; 11" BLACK 1 21590
U BRACKET; "L" 69-5319, STL 1 064353
V STUD; RUBBER MOUNT, M6X1” 1 02033
W BOLT; M6-1.00 X 25MM, SS 1 07858
X ADAPTER; FILTER, 3.0"OD 1 21569
Y HOSE CLAMP; #80 1 08694
Z FILTER CHARGER 1 RU-5163
PARTS LIST:
2. Release the spring clamp which secures the
crank case vent hose to the stock intake tube and
disconnect the crankcase vent hose from the intake
tube. Loosen the hose clamp the secures the
intake plenum/tube to the turbo inlet pipe and then
disconnect the plenum/tube from the turbo inlet
pipe.
3. Release the spring clamp that secures the BOV
hose to the intake tube and disconnect the BOV
hose from the intake tube. Loosen the hose clamp
securing the intake tube to the air lter housing and
then disconnect and remove the stock intake tube
from the vehicle.
4. Pop up the centers of the retaining clips that
secure the fresh air intake duct and then lift up the
intake duct to remove it from the vehicle.
5. Remove the two bolts that secure the air lter
housing and then remove the air lter housing from
the vehicle.
NOTE: K&N Engineering, Inc., recommends that
customers do not discard factory air intake.
6. Install the provided edge trim onto the heat
shield as shown.
NOTE: Some trimming of the edge trim will be
necessary.
A A
B
C
D
E
F
G
G
I
J
J
J
J
K
K
K
K
K
K
K
K
U
X
Y
Z
L
O
P
P
T
W
Q
Q
Q
R
R
S
O
M
N
V
H

Summary of content (3 pages)